Cargando…

Sending one arm of swiveling platform from Hanjung.

Departure fter paiing of the swiveling platform from Hanjung, Pusan, Korea.

Detalles Bibliográficos
Autor principal:	Hanjung
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42449

Ejemplares similares

First swiveleing of platform in SX5
por: Pascal Petiot
Publicado: (2002)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Production of Swiveling platform - Korea Visit during first stage of production 25th of April, 2001
por: A. PAYN, et al.
Publicado: (2001)

Production of Swiveling Platform in Korea - Visit during Machining - 12th/14th of June, 2001
por: Alain PAYN
Publicado: (2001)

Departure of pieces from swiveling platgorm from Dong Yang (Korea) on 3 September 2001.
por: Dong Yang
Publicado: (2001)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

One foot being machined at DWE
por: Franck Stach / ST-HM
Publicado: (2000)

One long tie bar broken after 3 days because of hydrogen contamination.
por: H. Gerwig
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Showing one of the air-pads applications used in CMS, for big loads translations in civil ingeneering.
por: Petiot Pascal
Publicado: (2000)

Control of the CMS coil swiveling platform - August 2001 - South Korea
por: C.Humbertclaude/C.Lasseur
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

Transfer of the cold box from SHL55 to USC55.
por: G. Perinic
Publicado: (2007)

Transfer of the cold box and its ancilliaries from SHL55 to USC55.
por: G. Perinic
Publicado: (2007)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

CERN survey team at KHI for photogrammetry of magnetic endcaps.Raphaël Goudard (CERN), Farshid Feyzi (from PSL) and Céline Humbertclaude (CERN) with KHI engineers.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Medial swivel dislocation of the talonavicular joint
por: Datt, NS, et al.
Publicado: (2009)

Snapshots of a molecular swivel in action
por: Trejo, Caitlin S, et al.
Publicado: (2018)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Assembly of minus endcap finished
por: Dick Loveless, et al.
Publicado: (2001)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Components of the test cryostat.
Publicado: (2001)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

CMS CONDUCTOR EBW PRODUCTION LINE AT TECHMETA - STATUS OF THE 17.01.01
por: Ramon Folch
Publicado: (2001)

YB0 central barrel assembly
por: Pascal Petiot
Publicado: (2001)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

Measurement of the location of tie-bar shoulders
por: Hubert Gerwig
Publicado: (2001)

Endcap support cart assembly finished Carts YE-3, YE-2, YE-1, Y+1, YE+2 compleleted assemblies shown in an overhead photo Several Subassemblies are also shown
por: Farshid Feyzi, et al.
Publicado: (2001)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_9qtpohttv0flujr4m6esbjbt8d