Cargando…

CMS conductor manufacturing at Techmeta by elecron beam welding

Detalles Bibliográficos
Autor principal:	Benoit CURE
Publicado:	2001
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42596

Ejemplares similares

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

CMS CONDUCTOR EBW PRODUCTION LINE AT TECHMETA - STATUS OF THE 17.01.01
por: Ramon Folch
Publicado: (2001)

Visit of the production line for the CMS electron beam welded conductor
por: Ramon Folch
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Construction of building extension at TECHMETA to accept EB line.
por: Ramon Folch
Publicado: (2000)

Full cross section of CMS conductor
por: Stefano Sgobba
Publicado: (2001)

EBW line assembly status for CMS conductor
por: Techmeta
Publicado: (2000)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Production of the Aluminium Alloy reinforcement bars for the CMS conductor at Alusuisse, Sierre, Switzerland
por: Alberto Calvo
Publicado: (2000)

Electron beam continuous welding unit
por: Ramon Folch
Publicado: (2000)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Continuous EB welding of the reinforcement of the CMS conductor
por: Tavares, S S, et al.
Publicado: (2002)

Continuous EB welding of the reinforcement of the CMS conductor
por: Folch, R, et al.
Publicado: (2002)

TECHMETA
Publicado: (2000)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Ferris Wheel welded structure before drilling and machining
por: Franz Leher, DWE, et al.
Publicado: (1999)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Conductor way-out Mock-up. September 2001 First trial of bending. Tensile Stress 120 Kg
por: Alain PAYN
Publicado: (2001)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

Manufacture of mandrels.
por: Ansaldo
Publicado: (2002)

Preheating to around 100°C under endcap blocks before welding at KHI.
por: Loveless, D
Publicado: (2000)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Quality monitoring of the electron beam welding of the CMS conductor using ultrasonics
por: Neuenschwander, J, et al.
Publicado: (2004)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Ancillary pieces for endcap carts being manufactured at HHM in Shanghai.
por: D. LOveless
Publicado: (2000)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Cannot write session to /tmp/vufind_sessions/sess_aj062a0jd51btr9bsirdrslu2s