Cargando…

Tensile test of final conductot

A tensile test of the conductor was conducted at EMPA. One expect also the aluminium alloy characteristics to increase 1) after impregnation and 2) after cooling at 4.2K

Detalles Bibliográficos
Autor principal:	Bertrand blau
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/42937

Ejemplares similares

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

End of cabling campaign at Brugg Kabelwerk in November 2002
por: Bertrand Blau
Publicado: (2002)

View of last estrusion operations at NEXANS (Cortaillod) in January 2003
por: Bertrand Blau
Publicado: (2003)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Conductor way-out Mock-up. September 2001 First trial of bending. Tensile Stress 120 Kg
por: Alain PAYN
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Picture of cabling operation, taken at Brugg Kabelwerk during the last campaign in November 2002
por: B. Blau
Publicado: (2002)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

View of stacking test.
por: Ansaldo
Publicado: (2000)

Components of the test cryostat.
Publicado: (2001)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Some tests systems in Saclay
por: F. Kircher
Publicado: (2002)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Etched and non etched test Rutherford cable.
por: S. Horvath
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Test to rupture of titanium tie-bars for the coil suspension.
por: Saclay
Publicado: (2000)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

View of SX hall beginning of March 2002.
por: Lucien Veillet
Publicado: (2002)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_sj57rdp2iimg73nqbnsl192b0u