Cargando…

Pictures of YB0 and nose.

Artistic pictures of YB0 and nose.

Detalles Bibliográficos
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43058

Ejemplares similares

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

YB0 central barrel assembly
por: Pascal Petiot
Publicado: (2001)

External vaccum vessel from YB0 (central barrel yoke) on Ferryswheel tool.
por: petiot Pascal
Publicado: (2000)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

YB-1 barrel yoke photogrametry on the ferryswheel
por: petiot Pascal
Publicado: (2000)

First movement for YB-2 barrel yoke
por: Petiot Pascal
Publicado: (2000)

Yoke barrel (YB-2) on grease pads under load
por: petiot Pascal
Publicado: (2000)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Picture of cabling operation, taken at Brugg Kabelwerk during the last campaign in November 2002
por: B. Blau
Publicado: (2002)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Factory acceptance of the compressor skids at Samifi-Babcock. All pictures show the second stage compressor skid.
por: G. Perinic
Publicado: (2001)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

CB0 wound
por: Ansaldo
Publicado: (2004)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Fixation of stabilizing tubes on Endcap disks
por: Lucien Veillet
Publicado: (2002)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

Some tests systems in Saclay
por: F. Kircher
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_kgirm1ltn4r983areubdpt3aq2