Cargando…

Trial insertion of inner vactank inside outer vactank.

Trial insertion of the inner vactank equipped with a coil mockup.

Detalles Bibliográficos
Autor principal:	Maximilien Brice
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43061

Ejemplares similares

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

HE+1 through vactank
por: Veillet
Publicado: (2003)

Measure by photogrammetry of outer vactank cylindricity after adjunction of the reinforcement rings.
por: Céline Humbertclaude
Publicado: (2001)

CMS - VACTANK CYLINDRICITY
por: Raphael GOUDARD, et al.
Publicado: (2002)

Inner Vactank on the swilling platform, YB-2
por: Jean-Frederic FUCHS, et al.
Publicado: (2003)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

View of inner and outer vacuum tanks
por: Maximilien Brice
Publicado: (2003)

Tracker VacTank Equipment Documentation Photos
por: Hoch, Michael
Publicado: (2009)

Measurement of the cylindricity of the CMS Inner Vactank before the insersion test - SX5 hall - Feb. 02
por: Raphael GOUDARD, et al.
Publicado: (2002)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

View of SX5 on 25/7/2002 before closure.
por: Brice maximilien
Publicado: (2002)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

Insertion of suspension shoulder for the coil
por: Franz leher, DWE, et al.
Publicado: (2000)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Conductor way-out Mock-up. September 2001 First trial of bending. Tensile Stress 120 Kg
por: Alain PAYN
Publicado: (2001)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Pictures of YB0 and nose.
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_7hjodcql0qi3lnqn93ehmtjimk