Cargando…

Mounting od HE-1 support tube

Tube support for HE-1 was inserted in YE-1

Detalles Bibliográficos
Autor principal:	Lucien Veillet
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43129

Ejemplares similares

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing tubes on Endcap disks
por: Lucien Veillet
Publicado: (2002)

HE+1 through vactank
por: Veillet
Publicado: (2003)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

View of muon cable trays on YE+2
por: Lucien Veillet
Publicado: (2003)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

Mounting of Blocks at DWE
por: Franck Stach, ST Division
Publicado: (2000)

View of SX hall beginning of March 2002.
por: Lucien Veillet
Publicado: (2002)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of HE support tube from Minsk
por: L. Veillet
Publicado: (2002)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Installation of ME1/1 Support Disk on HE-1
por: Lucien Veillet
Publicado: (2002)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

Support structure Ferris Wheel
por: Franz Leher, DWE, et al.
Publicado: (1999)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Start assembly of HE-1
por: Lucien Veillet
Publicado: (2002)

End of assembly of HE-1
por: Lucien Veillet
Publicado: (2002)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Right and left support feet of the Central Barrel Yoke of the CMS Detector
por: Franz Leher, DWE, et al.
Publicado: (2000)

Endcap support cart assembly finished Carts YE-3, YE-2, YE-1, Y+1, YE+2 compleleted assemblies shown in an overhead photo Several Subassemblies are also shown
por: Farshid Feyzi, et al.
Publicado: (2001)

Low-Cost Clamp-On Photometers (ClampOD) and Tube Photometers (TubeOD) for Online Cell Density Determination
por: Deutzmann, Jörg S., et al.
Publicado: (2022)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Installation of first 80 ton slice of HE-1
por: Lucien Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_697488fjq6tno59mb7bsp1mqhc