Cargando…

Fixation of neutron shielding on YN-1

Neutron shielding (polyethylene + lead) must be fixed on nose before mounting HE-1

Detalles Bibliográficos
Autor principal:	Lucien Veillet
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43161

Ejemplares similares

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing tubes on Endcap disks
por: Lucien Veillet
Publicado: (2002)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

View of muon cable trays on YE+2
por: Lucien Veillet
Publicado: (2003)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

View of SX hall beginning of March 2002.
por: Lucien Veillet
Publicado: (2002)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

HE+1 through vactank
por: Veillet
Publicado: (2003)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Drilling of YE for neutron shielding
por: L. Veillet
Publicado: (2002)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Pictures of YB0 and nose.
Publicado: (2002)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_ii3r0tab4lpqr9qbed9t1g99in