Cargando…

Impregnation chamber close with prototype inside

View of insulated impregnation chamber.

Detalles Bibliográficos
Autor principal:	Ansalso
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43470

Ejemplares similares

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Winding of prototype.
por: Ansaldo
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

Photos of endcap disk connection prototype
por: Farshid Feyzi
Publicado: (2000)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

Prototype of corner piece between two endcap disks.
por: F. Feyzi
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Pictures of YB0 and nose.
Publicado: (2002)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Fixation of stabilizing tubes on Endcap disks
por: Lucien Veillet
Publicado: (2002)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

Some tests systems in Saclay
por: F. Kircher
Publicado: (2002)

Picture of cabling operation, taken at Brugg Kabelwerk during the last campaign in November 2002
por: B. Blau
Publicado: (2002)

End of cabling campaign at Brugg Kabelwerk in November 2002
por: Bertrand Blau
Publicado: (2002)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

Manufacture of mandrels.
por: Ansaldo
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_2ac75c0umi1m4jamp9m24dhdvg