Cargando…

Manufacture of mandrels.

CB-2 is finished, CB-1 is ready for machining and CB0 is ready for welding

Detalles Bibliográficos
Autor principal:	Ansaldo
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43471

Ejemplares similares

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

Construction of mandrel CB-2
por: Ansaldo
Publicado: (2002)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

Last layer of CB-2
por: Ansaldo
Publicado: (2003)

Winding of prototype.
por: Ansaldo
Publicado: (2002)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

View of stacking test.
por: Ansaldo
Publicado: (2000)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Coupling of CB-2 and CB-1
por: Ansaldo
Publicado: (2003)

CB0 wound
por: Ansaldo
Publicado: (2004)

Situation of CB+1/CB+2 mid January 2004
por: Ansaldo
Publicado: (2004)

Loading CB-2 on board
por: Ansaldo
Publicado: (2004)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

Ancillary pieces for endcap carts being manufactured at HHM in Shanghai.
por: D. LOveless
Publicado: (2000)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

A New Disc Mandrel
Publicado: (1892)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Pictures of YB0 and nose.
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_dqt25vkt2tcr8tcq7954e12iis