Cargando…

An electroplating fabrication method for electron accelerator structures

Detalles Bibliográficos
Autores principales:	Matsumoto, H, Shintake, T, Iino, Y, Kabeya, Zenzaburo
Lenguaje:	eng
Publicado:	1998
Materias:	Engineering
Acceso en línea:	http://cds.cern.ch/record/434822

Ejemplares similares

Fabrication of the C-band (5712 MHz) Choke-Mode type damped accelerator structure
por: Matsumoto, H, et al.
Publicado: (1998)

Electroplating of lead free solder for electronics
por: Joseph, Shany, et al.
Publicado: (2011)

Experience On The High-power Sic Microwave Dummy-load Using Sic Absorber
por: Matsumoto, H, et al.
Publicado: (1999)

Modern electroplating
por: Lowenheim, Frederick A
Publicado: (1966)

High power test of HOM-free choke-mode damped accelerating structure
por: Shintake, T, et al.
Publicado: (1995)

Electroplating engineering handbook
por: Graham, A Kenneth
Publicado: (1971)

Electroplating engineering handbook...
por: Graham, A Kenneth
Publicado: (1955)

Principles of electroplating and electroforming (electrotyping)
por: Blum, William, et al.
Publicado: (1949)

HOM-free linear accelerating structure for e+e- linear collider at C-band
por: Shintake, T, et al.
Publicado: (1996)

Low temperature brazing technique for accelerators
por: Matsumoto, H, et al.
Publicado: (1996)

Electroplating Of Proton Linear Accelerator Tanks
por: Tanaka, J, et al.
Publicado: (1971)

Precise fabrication of X-band detuned accelerating structure for linear collider
por: Higo, T, et al.
Publicado: (1996)

Laser-Assisted Selective Fabrication of Copper Traces on Polymers by Electroplating
por: Fiodorov, Vitalij, et al.
Publicado: (2022)

Development of C-band 50 MW pulse klystron for $e^{+}e^{-}$ linear collider
por: Shintake, T, et al.
Publicado: (1998)

Electrospinning and electroplating
por: Jacobs, Toby
Publicado: (2017)

Optimization on wakefield damping in C-band accelerating structure
por: Akasaka, N, et al.
Publicado: (1998)

Fabrication and Characterization of Flexible Thermoelectric Generators Using Micromachining and Electroplating Techniques
por: Lee, Wnag-Lin, et al.
Publicado: (2019)

Fabrication of X-ray Gratings for Interferometric Imaging by Conformal Seedless Gold Electroplating
por: Jefimovs, Konstantins, et al.
Publicado: (2021)

Pulsed modulator for C-band klystron
por: Baba, H, et al.
Publicado: (1998)

C-band klystron and RF-system development
por: Shintake, T, et al.
Publicado: (1997)

TM0,1.5,0 mode cavity for longitudinal bunch feedback kicker
por: Shintake, T
Publicado: (1996)

C-band choke mode accelerator structure for the linear collider
por: Matsumoto, H, et al.
Publicado: (1996)

Active mover using air-spring and MLRB
por: Takeda, S, et al.
Publicado: (1997)

Fabrication and Optimization of High Aspect Ratio Through-Silicon-Vias Electroplating for 3D Inductor
por: Li, Haiwang, et al.
Publicado: (2018)

Multifunctional Electrically Conductive Copper Electroplated Fabrics Sensitizes by In-Situ Deposition of Copper and Silver Nanoparticles
por: Ali, Azam, et al.
Publicado: (2021)

C-band linac rf-system for e+e- linear collider
por: Shintake, T, et al.
Publicado: (1996)

Alignment issues for C-band Linear Collider
por: Kubo, K, et al.
Publicado: (1996)

A new RF pulse-compressor using multi-cell coupled-cavity system
por: Shintake, T, et al.
Publicado: (1996)

Electroplating lithium transition metal oxides
por: Zhang, Huigang, et al.
Publicado: (2017)

Electroplating and Ablative Laser Structuring of Elastomer Composites for Stretchable Multi-Layer and Multi-Material Electronic and Sensor Systems
por: Stier, Simon P., et al.
Publicado: (2021)

Effect of Cu Ion Concentration on Microstructures and Mechanical Properties of Nanotwinned Cu Foils Fabricated by Rotary Electroplating
por: Hung, Yu-Wen, et al.
Publicado: (2021)

Workshop for Semiconductor Fabrication and Accelerator Technology: Contamination, its Measurement and Control in Vacuum Systems
por: Collective
Publicado: (1997)

Quantitative Analysis of Electroplated Nickel Coating on Hard Metal
por: Wahab, Hassan A., et al.
Publicado: (2013)

Standalone, battery powered radiation monitors for accelerator electronics
por: Wijnands, T, et al.
Publicado: (2009)

Fabrication Engineering for Accelerator Components
por: Garlasche, Marco, et al.
Publicado: (2022)

Insulation systems for $Nb_{3}$Sn accelerator magnet coils fabricated by the "wind and react" technique
por: Devred, Arnaud, et al.
Publicado: (1999)

Straightness measurements for accelerator structures
por: Schwarz, W
Publicado: (1995)

Fabrication of porous gallium nitride by photoelectrochemical etching method
por: Cheah, Sook Fong, et al.
Publicado: (2017)

Electronic methods
por: Haxby, Robert Ozias, et al.
Publicado: (1975)

Electronic methods
por: Haxby, Robert Ozias, et al.
Publicado: (1975)

Cannot write session to /tmp/vufind_sessions/sess_97hgkpo01jbkq5rhgbbuiituf9