Cargando…

Winding Prototype has been impregnated.

Impregnatiuon of winding prototype has been completed successfully.

Detalles Bibliográficos
Autor principal:	Ansaldo
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43525

Ejemplares similares

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Winding of prototype.
por: Ansaldo
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

Winding model completed on the transferring tool at ANSALDO.
por: Ansaldo, M
Publicado: (2000)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Manufacture of mandrels.
por: Ansaldo
Publicado: (2002)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

Last layer of CB-2
por: Ansaldo
Publicado: (2003)

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

Construction of mandrel CB-2
por: Ansaldo
Publicado: (2002)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

View of stacking test.
por: Ansaldo
Publicado: (2000)

Coupling of CB-2 and CB-1
por: Ansaldo
Publicado: (2003)

CB0 wound
por: Ansaldo
Publicado: (2004)

Situation of CB+1/CB+2 mid January 2004
por: Ansaldo
Publicado: (2004)

Loading CB-2 on board
por: Ansaldo
Publicado: (2004)

Elements of the winding machine at TPA.
por: P. Fabbricatore
Publicado: (2001)

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

Photos of endcap disk connection prototype
por: Farshid Feyzi
Publicado: (2000)

Prototype of corner piece between two endcap disks.
por: F. Feyzi
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_a981jpkrl1vcdd3ku80d8a0387