Cargando…

Some tests systems in Saclay

Tests of tie-rod insertion, tie-rod test system, thermal screen and braid for current leads

Detalles Bibliográficos
Autor principal:	F. Kircher
Lenguaje:	ENG
Publicado:	2002
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43613

Ejemplares similares

Coil cross-section Mock-up done by CEA / Saclay April 2002
por: A. PAYN
Publicado: (2002)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Montage photograph: Cryogenic components mounted on top of the central yoke barrel in the configuration for the acceptance tests of the helium refrigeration system comprising the intermediate cryostat (right), the test cryostat (left) and the cryogenic transfer lines.
por: Goran Perinic
Publicado: (2003)

View of stacking test.
por: Ansaldo
Publicado: (2000)

Components of the test cryostat.
Publicado: (2001)

Tensile test of final conductot
por: Bertrand blau
Publicado: (2002)

Test of threads for superbolts at KHI.
por: Loveless, D
Publicado: (2000)

Zstop end cap load test
por: Pascal Petiot
Publicado: (2003)

Etched and non etched test Rutherford cable.
por: S. Horvath
Publicado: (2000)

First test of EBW line with 3 components at Techmeta
por: R. Folch
Publicado: (2001)

Test to rupture of titanium tie-bars for the coil suspension.
por: Saclay
Publicado: (2000)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

Test of a sector block under a 400 ton press at KHI.
por: Loveless, D
Publicado: (2000)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Spooling of a dummy conductor during the preliminary test of the pay-off units and the spooler for the EBW production line.
por: R. Folch
Publicado: (2000)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

First winding tests at Siegen using the final winding machine and the dummy conductor with 99.5% pure aluminium insert and no Rutherford cable.
por: Ansaldo
Publicado: (2001)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

Pictures of YB0 and nose.
Publicado: (2002)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Situation of winding end of August 2002
por: Ansaldo
Publicado: (2002)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Machining of mandrel
por: Ansaldo
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_hufll46h4jdft8r8namgo9asc7