Cargando…

Post for CSC installed on YE-2

All the posts for endcap muon chambers were installed on YE-2 disk in Februruay-March, 2003. Installation proceeded without problems.

Detalles Bibliográficos
Autor principal:	Dan Wenman
Lenguaje:	ENG
Publicado:	2003
Materias:	Muon Detector
Acceso en línea:	http://cds.cern.ch/record/43663

Ejemplares similares

CSC posts ready for shipment
por: Dan Wenman
Publicado: (2002)

First test of mounting a CSC on YE-2
por: Walter van Doninck
Publicado: (2001)

CSC installation fixture finished
por: Farshid Feyzi, et al.
Publicado: (2001)

Completion of cathode strip chamber (CSC) installation on the so-called YE+2 wheel of CMS on March 2005.
por: Tejinder S. Virdee
Publicado: (2005)

Instalation of first endcap Muons station on YE+1
Publicado: (2005)

Installation of Muon Endcap Station 1 on YE+1
Publicado: (2005)

Installation of ME1/2 + RE1/2 packages on YE+1
Publicado: (2005)

Installation of ME1/1 Dubna chambers on the endcap disk YE-1
Publicado: (2005)

Images of the CMS Muons - Cathode Strip Chambers (CSC)
por: Breedon, R, et al.
Publicado: (2008)

Installation of Endcap Muon Chambers
por: Dan Wenman
Publicado: (2003)

CMS RPC detectors assembled in Pakistan installed on the backside of the YE+1 endcap yoke
por: Walter Van Doninck, VUB-Brussels and CERN
Publicado: (2006)

Pictures showing the test of CSC installation fixture. The CSC is fully balanced and free to rotate to any angle. After CSC is attached to mounts, fixture is rebalanced and removed. Electrical limits stops are set at with or without chamber balance points.
por: Farshid Feyzi, et al.
Publicado: (2001)

Lowering of YE+2 disk
por: Max Brice, CERN
Publicado: (2006)

A view of YE+1 after the installation of the first layer of RE1/3 RPC chambers.
Publicado: (2006)

Completion of cathode strip chamber (CSC) installation on the "plus" endcap of CMS
por: Richard Breedon, UC Davis
Publicado: (2006)

CMS Cathode Strip Chambers (CSC) extraction
por: Lapka, Marzena
Publicado: (2019)

Photogrammetry of the new CSC chambers at the CMS Experiment
por: Behrens, Antje, et al.
Publicado: (2013)

Lowering of the YE+3 endcap disc on 30th November
por: Max Brice, CERN
Publicado: (2006)

Installation of the first Cathode Strip Chambers (CSC) of CMS at P5 (Cessy, France) on June 2003
Publicado: (2003)

Installation of muon chambers on endcap
por: Farshid Feyzi
Publicado: (2004)

Test installation of MB1
por: Alberto Benvenuti
Publicado: (2002)

Installation of ME1/1 Support Disk on HE-1
por: Lucien Veillet
Publicado: (2002)

Installation of Barrel Muon stations (DTs and RPCs) in the two mobile wheels YB+1 and YB+2 is complete.
Publicado: (2005)

An Endcap Muon CSC with a prototype cooling plate mounted on the chamber frame. Visible are the aluminum cover supports that mount between the cathode front-end boards.
por: Sergei Lusin
Publicado: (2000)

First CMS Gas Electron Multipliers (GEMs) installation
por: Lapka, Marzena
Publicado: (2019)

Installation of some Cathode Strip Chambers on March 2004
por: Richard Breedon
Publicado: (2004)

Installation of last DT+RPC packages for the muon barrel detector of CMS
por: Jesus Puerta-Pelayo
Publicado: (2007)

Assembly of a CSC detector for the dimuon tracking system in a clean room at Cagliari (Italy).
por: Saba, A
Publicado: (2005)

An ME234/2 EMU chamber with a laminated prototype cooling plate mounted. Dummy cathode boards and cathode board covers are installed.
por: Sergei Lusin
Publicado: (2000)

Completion of installation of DT and RPC chambers before Cosmic Challenge
por: Mimmo Dattola
Publicado: (2006)

First installation of DT and RPC packages into the CMS iron yoke
por: Jesus Puerta-Pelayo
Publicado: (2004)

Endcap Muon Low Voltage Power Supply Prototype
por: Farshid Feyzi
Publicado: (2002)

Installation of station 1 of the tracking chambers of the ALICE Muon Spectrometer
por: Suire, Christophe
Publicado: (2007)

Installation of the front-end electronics of the muon spectrometer tigger chambers
por: Saba, A
Publicado: (2006)

Installation of the front-end electronics of the muon spectrometer tigger chambers
por: Saba, A.
Publicado: (2006)

First DT+RPC chambers installation round in the UX5 cavern
por: Jesus Puerta-Pelayo
Publicado: (2007)

ALICE Dimuon: Installing the station 5 tracking chamber in the test beam area.
por: Cicalo, C.
Publicado: (2004)

MWPC cathode plane. Prototype built in Oct 2000
por: Schneider, T
Publicado: (2000)

Last Muon DT SuperLayer glued in Legnaro
por: Paolo Checchia
Publicado: (2005)

First Cosmic muon seen in four barrel muon stations at point 5 on 13 December 2005
por: Gianni Masetti
Publicado: (2005)

Cannot write session to /tmp/vufind_sessions/sess_bi6tahiki5osehfchcej2vn713