Cargando…

View of inner and outer vacuum tanks

View of inner vacuum tank on swiveling platform and external vacuum tank in YB0.

Detalles Bibliográficos
Autor principal:	Maximilien Brice
Lenguaje:	ENG
Publicado:	2003
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/43673

Ejemplares similares

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Internal cylinder from vacuum tank of the cryostat
por: Pascal Petiot
Publicado: (2000)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

View of SX5 on 25/7/2002 before closure.
por: Brice maximilien
Publicado: (2002)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Helium Tank for Cryoplant
por: Dupont Thierry
Publicado: (2001)

Two shells of external Vac Tank
por: Franck Stach / ST-HM
Publicado: (2000)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Ultrasonic tests of the weld between black and stainless steel in the radial rib of the of the central barrel. It constitutes the connection between vacuum tank and the barrel yoke.The plate is of 75 mm thickness and it is a full penetration weld.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

View of muon cable trays on YE+2
por: Lucien Veillet
Publicado: (2003)

Measure by photogrammetry of outer vactank cylindricity after adjunction of the reinforcement rings.
por: Céline Humbertclaude
Publicado: (2001)

View of last estrusion operations at NEXANS (Cortaillod) in January 2003
por: Bertrand Blau
Publicado: (2003)

View of stacking test.
por: Ansaldo
Publicado: (2000)

Fish-eye view of yoke
por: service photo
Publicado: (2002)

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

View of new cabling machine at Brugg Kabelwerke
por: S. Horvath
Publicado: (2000)

View of SX hall beginning of March 2002.
por: Lucien Veillet
Publicado: (2002)

View of the photogrammetric targets for the first YE1 at KHI.
por: C. Humbertclaude
Publicado: (2000)

View of the fillers on top of the winding model to get a flat interface.
por: ANSALDO, E
Publicado: (2000)

View of old cabling machine at Brugg Kabelwerke for 280m CMS Rutherford cable.
por: S. Horvath
Publicado: (2000)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Mathematicians: an outer view of the inner world
por: Cook, Mariana
Publicado: (2009)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_kn3ia5bb9gtg9q8tri7q6biqod