Cargando…

The vacuum bellows and the optimization of their shielding

Detalles Bibliográficos
Autores principales:	Unterlerchner, W, Zotter, Bruno W
Lenguaje:	eng
Publicado:	1986
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/443447

Ejemplares similares

Current limitations in LEP due to vacuum chamber bellows
por: Zotter, Bruno W
Publicado: (1985)

Longitudinal and transverse impedances of bellows in the low frequency range
por: Kheifets, S A, et al.
Publicado: (1986)

Energy loss in the tapers and bellows of the LEP super conducting cavity modules
por: Zotter, Bruno W
Publicado: (1992)

Broad-band impedance of LHC shielded bellows
por: Dyachkov, M, et al.
Publicado: (1998)

APS SR Flexible Bellows Shield Performance
por: Jones, J, et al.
Publicado: (1999)

Specification for bellows to be used in HT vacuum relay
por: Hoekemeijer, F
Publicado: (1979)

Non-standard vacuum hardware for an accelerator vacuum system
por: Unterlerchner, W
Publicado: (1990)

Observation and calculation of trapped modes near cut-off in the ALS bellows-shield
por: Corlett, J N
Publicado: (1996)

Specification for the manufacture of high frequency finger contacts for the vacuum-bellow systems
por: CERN. Geneva
Publicado: (1987)

Expected vacuum conditions in the PSB
por: Unterlerchner, W
Publicado: (1969)

Characterization of the RF Fingers Contact Force for the LHC Warm Vacuum Bellow Modules
por: Blanch Gutiérrez, Cesar, et al.
Publicado: (2015)

Booster Vacuum system - Chamber to Chamber Insulation
por: Unterlerchner, W
Publicado: (1968)

Specification for vacuum manifold (light type) for the Synchrotron Injector Ring
por: Unterlerchner, W
Publicado: (1969)

Specification for sector valves for the Synchrotron Injector (Booster) vacuum system
por: Unterlerchner, W
Publicado: (1970)

Specification for vacuum chambers and tubes of the first part of the injection line - Booster
por: Unterlerchner, W
Publicado: (1970)

Impedance of bellows corrugations
por: Ng, K Y
Publicado: (1987)

Impedances Of RF Bellows
por: Henke, H
Publicado: (1983)

Specification for vacuum chambers in the triplet sections of the 800 MeV synchrotron injector
por: Unterlerchner, W
Publicado: (1970)

Specification for vacuum chambers inside 800 MeV Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

The influence of the mechanical properties of gasket materials on the reliability of bakeable ultrahigh vacuum flanges
por: Unterlerchner, W
Publicado: (1977)

Technical specification for supply of ∅140 and ∅150 mm bellows (For subsequent incorporation into quadrupole vacuum vessels)
Publicado: (1984)

Shielding effects on coherent synchrotron radiation
por: Kheifets, S A, et al.
Publicado: (1995)

Specification of ceramic vacuum pipes for injection kicker and beam transformers of the Proton Synchrotron Booster
por: Unterlerchner, W
Publicado: (1970)

The influence of vacuum annealing, glow discharge and electropolishing on the topography of stainless steel sheet metal
por: Unterlerchner, W
Publicado: (1977)

Specification for the manufacture of mechanical components for the vacuum-bellow systems - 1st revision 25/9/87
por: CERN. Geneva
Publicado: (1987)

Technical specification for flexible metal bellows (compensators) for the vacuum system of the 400 GeV proton accelerator
por: Wahl, H
Publicado: (1977)

Technical specification for flexible metal bellows (compensators) for the vacuum system of the 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1980)

Low cost vacuum hardware developed for the CERN PS Booster
por: Rufer, C E, et al.
Publicado: (1971)

LHC Bellows Impedance Calculations
por: Dyachkov, M, et al.
Publicado: (1997)

The impedance of layered vacuum chambers
por: Keil, Eberhard, et al.
Publicado: (1998)

Shielding Particle Beams by Thin Conductors
por: Gluckstern, R L, et al.
Publicado: (2002)

Analysis of Shielding Charged Particle Beams by thin Conductors
por: Gluckstern, R L, et al.
Publicado: (2001)

Tune shifts of excentric beams in elliptic vacuum chambers
por: Zotter, Bruno W
Publicado: (1975)

PS vacuum system : new model of bellows mounted on the vacuum chamber
por: CERN PhotoLab
Publicado: (1964)

Impedance of Layered Vacuum Chambers for Large Colliders
por: Keil, Eberhard, et al.
Publicado: (1998)

Image fields of an off-centre particle beam in an elliptic vacuum chamber
por: Zotter, Bruno W
Publicado: (1974)

Transverse oscillations of a relativistic particle beam in a laminated vacuum chamber
por: Zotter, Bruno W
Publicado: (1969)

A short review of some aspects of the Booster vacuum system (RING)
por: Brianti, G, et al.
Publicado: (1968)

Energy Loss to Coaxial Vacuum Chambers in LEP and LHC
por: Gluckstern, R L, et al.
Publicado: (1996)

Specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges, and vacuum tubes for the magnets in the Experimental Areas of the 450 GeV Proton Synchrotron
por: CERN. Geneva
Publicado: (1982)

Cannot write session to /tmp/vufind_sessions/sess_acvt5dnlcf99541r42pjtg0t9l