Cargando…

Computer-aided design (CAD) technique - use of computers forthe preparation of construction drawings

Detalles Bibliográficos
Autor principal:	International Organization for Standardization. Geneva
Lenguaje:	eng
Publicado:	ISO 1990
Materias:	Information Transfer and Management
Acceso en línea:	http://cds.cern.ch/record/477647

Ejemplares similares

Technical drawings - general principles of presentation: Part 21 : preparation of lines by cad systems
por: International Organization for Standardization. Geneva
Publicado: (1997)

Construction drawings - landscape drawing practice
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - construction drawings - general principles of presentation for general arrangement and assembly drawings
por: International Organization for Standardization. Geneva
Publicado: (1991)

Construction drawings: Part 1 : Buildings and parts of buildings
por: International Organization for Standardization. Geneva
Publicado: (1998)

Technical drawings: Scales
por: International Organization for Standardization. Geneva, et al.
Publicado: (1979)

Optics and optical instruments - preparation of drawings for opticalelements and systems: Part 6 : centring tolerances
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings: Datums and datum-systems for geometrical tolerances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1981)

Microfilming of technical drawings and other drawing office documents: Part 4 : microfilming of drawings of special and exceptional elongated sizes
por: International Organization for Standardization. Geneva
Publicado: (1994)

Optics and optical instruments - preparation of drawings for opticalelements and systems: Part 11 : non-toleranced data
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings: Cones
por: International Organization for Standardization. Geneva
Publicado: (1990)

Technical drawings: Guidelines
por: International Organization for Standardization. Geneva
Publicado: (1985)

Microfilming of technical drawings and other drawing office documents: Part 1 : Operating procedures
por: International Organization for Standardization. Geneva
Publicado: (1983)

Technical drawings: Part 1 : Graphical symbols for plumbing, heating, ventilation and ducting
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Building and civil engineering drawings : installations: part 2 : simplified representation of sanitary appliances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1980)

Technical drawings: Fundamental tolerancing principle
por: International Organization for Standardization. Geneva
Publicado: (1985)

Technical drawings: Dimensioning and tolerancing of profiles
por: International Organization for Standardization. Geneva
Publicado: (1987)

Microfilming of technical drawings and other drawing office documents: Part 3 : Aperture card for 35 mm microfilm
por: International Organization for Standardization. Geneva
Publicado: (2001)

Technical drawings : installations: part 6 : graphical symbols for supply water and drainage systems in the ground
por: International Organization for Standardization. Geneva, et al.
Publicado: (1985)

Technical drawings: Tolerancing of linear and angular dimensions
por: International Organization for Standardization. Geneva
Publicado: (1987)

Technical drawings: Maximum material principle
por: International Organization for Standardization. Geneva, et al.
Publicado: (1988)

Draughting media for technical drawings - natural tracing paper
por: International Organization for Standardization. Geneva
Publicado: (1992)

Technical drawings : simplified representation of moulded, cast and forged parts
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - projection methods: Part 3 : axonometric representations
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings - tolerancing of orientation and location projected tolerance zone
por: International Organization for Standardization. Geneva
Publicado: (1992)

Technical drawings - rolling bearings: Part 2 : detailed simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - general principles of presentation: Part 20 : basic conventions for lines
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings - screw threads and threaded parts: Part 1 : general conventions
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - screw threads and threaded parts: Part 2 : screw thread inserts
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - simplified representation of the assembly of parts with fasteners: Part 2 : rivets for aerospace equipment
por: International Organization for Standardization. Geneva
Publicado: (1995)

Draughting media for technical drawings - draughting film with polyester base: Part 1 : requirements and marking
por: International Organization for Standardization. Geneva
Publicado: (1992)

Draughting media for technical drawings - draughting film with polyester base: Part 2 : determination of properties
por: International Organization for Standardization. Geneva
Publicado: (1992)

Numerically controlled draughting machines - drawing test for the evaluation of performance: Part 1 : vector plotters
por: International Organization for Standardization. Geneva
Publicado: (1992)

Technical product documentation - handling of computer-based technical information: Part 3 : phases in the product design process
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical product documentation - handling of computer-based technical information: Part 1 : security requirements
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical product documentation - handling of computer-based technical information: Part 2 : original documentation
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical product documentation - handling of computer-based technical information: Part 4 : document management and retrieval systems
por: International Organization for Standardization. Geneva
Publicado: (1993)

Rubber and plastics hoses and hose assemblies: Ratios of proof and burst pressure to design working pressure
por: International Organization for Standardization. Geneva, et al.
Publicado: (1991)

Pipe threads where pressure-tight joints are made on the threads: part 1 : dimensions, tolerances and designation
por: International Organization for Standardization. Geneva, et al.
Publicado: (1994)

Sintered metal materials, excluding hardmetals: Determination of transverse rupture strength
por: International Organization for Standardization. Geneva, et al.
Publicado: (1996)

Hydraulic fluid power: filter elements : verification of material compatibility with fluids
por: International Organization for Standardization. Geneva, et al.
Publicado: (1998)

Cannot write session to /tmp/vufind_sessions/sess_51su6b7k72jpgoq75bbb9f2umt