Cargando…

Templates for lettering and symbols: Part 3 : slot widths for technical pens with tubular tips in accordance with ISO 9175-1

Detalles Bibliográficos
Autor principal:	International Organization for Standardization. Geneva
Lenguaje:	eng
Publicado:	ISO 1989
Materias:	Engineering
Acceso en línea:	http://cds.cern.ch/record/484885

Ejemplares similares

Templates for lettering and symbols: Part 2 : slot widths for wood-cased pencils, clutch pencils and fine-lead pencils
por: International Organization for Standardization. Geneva
Publicado: (1988)

Tubular technical pens: adaptor for compasses
por: International Organization for Standardization. Geneva
Publicado: (1988)

Tubular tips for hand-held technical pens using india ink on tracing paper: Part 1 : definitions, dimensions, designation and marking
por: International Organization for Standardization. Geneva
Publicado: (1988)

Tubular tips for hand-held technical pens using india ink on tracing paper: Part 2 : performance, test parameters and test conditions
por: International Organization for Standardization. Geneva
Publicado: (1988)

Technical drawings: Part 1 : Graphical symbols for plumbing, heating, ventilation and ducting
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Technical drawings - symbols for geometrical tolerancing proportions and dimensions
por: International Organization for Standardization. Geneva
Publicado: (1983)

Templates for lettering and symbols: Part 1 : general principles and identification markings
por: International Organization for Standardization. Geneva
Publicado: (1988)

Technical product documentation: Part 3: applications of ISO-13567-1 and ISO-13567-2
por: International Organization for Standardization. Geneva
Publicado: (1999)

Technical drawings : installations: part 6 : graphical symbols for supply water and drainage systems in the ground
por: International Organization for Standardization. Geneva, et al.
Publicado: (1985)

Technical drawings: symbolic presentation and indication of adhesive, fold and pressed joints
por: International Organization for Standardization. Geneva
Publicado: (2002)

Slotted pan head tapping screws
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Slotted set screws with cone point
por: International Organization for Standardization. Geneva
Publicado: (1983)

Slotted set screws with cup point
por: International Organization for Standardization. Geneva
Publicado: (1983)

Process measurement control functions and instrumentation : symbolic representation: part 3 : detailed symbols for instrument interconnection diagrams
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Slotted countersunk (flat) head tapping screws (common head style)
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

The ISO standards compendium ISO 9000 - Quality management
por: International Organization for Standardization. Geneva
Publicado: (2001)

Slotted raised countersunk (oval) head tapping screws (common head style)
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Welded, brazed and soldered joints: symbolic representation on drawings
por: International Organization for Standardization. Geneva, et al.
Publicado: (1992)

Welding and allied processes: symbolic representation on drawings : welded joints
por: International Organization for Standardization. Geneva, et al.
Publicado: (2013)

ISO 9000: quality management
por: International Organization for Standardization. Geneva
Publicado: (1996)

Quantities and units, ISO 31
por: International Organization for Standardization. Geneva
Publicado: (1992)

Hexagon bolts for high-strength structural bolting with large width across flats (thread lengths according to 888): Property classes 8.8 and 10.9
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Information to assist forestry organizations in the use of Environmental Management System standards ISO 14001 and ISO 14004
por: International Organization for Standardization. Geneva
Publicado: (1998)

Unités de mesure, ISO 31
por: International Organization for Standardization. Geneva
Publicado: (1979)

Terminology and symbols; plastics in general; reinforced plastics
por: International Organization for Standardization. Geneva
Publicado: (1990)

Process measurement control functions and instrumentation : symbolic representation: part 1 : basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1977)

Process measurement control functions and instrumentation : symbolic representation: part 2 : extension of basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

ISO 9000: international standards for quality management
por: International Organization for Standardization. Geneva
Publicado: (1992)

ISO 9000 management de la qualite
por: International Organization for Standardization. Geneva
Publicado: (1996)

Ball point pens and refills: Part 2: documentary use (DOC)
por: International Organization for Standardization. Geneva
Publicado: (1998)

Roller ball pens and refills: Part 2: Documentary use (DOC)
por: International Organization for Standardization. Geneva
Publicado: (1998)

Technical drawings: Scales
por: International Organization for Standardization. Geneva, et al.
Publicado: (1979)

Information pour assister les organismes forestiers dans l'utilisation des normes ISO 14001 et ISO 14004 relatives aux systèmes de management environnemental
por: International Organization for Standardization. Geneva
Publicado: (1998)

Technical product documentation - Vocabulary - Part 1: terms relating to technical drawings: general and types of drawings
por: International Organization for Standardization. Geneva, et al.
Publicado: (1992)

Technical drawings: Maximum material principle
por: International Organization for Standardization. Geneva, et al.
Publicado: (1988)

Hexagon nuts for structural bolting with large width across flats, style 1: Property class 10
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Technical drawings: Datums and datum-systems for geometrical tolerances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1981)

Technical drawings
por: International Organization for Standardization. Geneva
Publicado: (1991)

Technical drawings
por: International Organization for Standardization. Geneva
Publicado: (2002)

Technical drawings
por: International Organization for Standardization. Geneva
Publicado: (2002)

Cannot write session to /tmp/vufind_sessions/sess_4gjta9gva2dksjs9oclidvoce3