Cargando…

Draughting instruments with or without graduation: Part 1 : draughting scale rules

Detalles Bibliográficos
Autor principal:	International Organization for Standardization. Geneva
Lenguaje:	eng
Publicado:	ISO 1992
Materias:	Information Transfer and Management
Acceso en línea:	http://cds.cern.ch/record/485019

Ejemplares similares

Draughting instruments with or without graduation: Part 2 : protractors
por: International Organization for Standardization. Geneva
Publicado: (1994)

Draughting instruments with or without graduation: Part 3 : set squares
por: International Organization for Standardization. Geneva
Publicado: (1994)

Draughting media for technical drawings - draughting film with polyester base: Part 1 : requirements and marking
por: International Organization for Standardization. Geneva
Publicado: (1992)

Draughting media for technical drawings - draughting film with polyester base: Part 2 : determination of properties
por: International Organization for Standardization. Geneva
Publicado: (1992)

Manually operated draughting machines: Part 3 : dimensions of scale rule chuck plates
por: International Organization for Standardization. Geneva
Publicado: (1994)

Manually operated draughting machines: Part 1 : definitions, classification and designation
por: International Organization for Standardization. Geneva
Publicado: (1992)

Manually operated draughting machines: Part 2 : characteristics, performance, inspection and marking
por: International Organization for Standardization. Geneva
Publicado: (1992)

Draughting media for technical drawings - natural tracing paper
por: International Organization for Standardization. Geneva
Publicado: (1992)

Fluid draughting media: Part 1 : water-based india ink - requirements and test conditions
por: International Organization for Standardization. Geneva
Publicado: (1992)

Numerically controlled draughting machines - drawing test for the evaluation of performance: Part 1 : vector plotters
por: International Organization for Standardization. Geneva
Publicado: (1992)

Fluid draughting media: Part 2 : water-based non-india ink - requirements and test conditions
por: International Organization for Standardization. Geneva
Publicado: (1995)

Numerically controlled draughting machines: Part 2: monochrome raster plotters
por: International Organization for Standardization. Geneva
Publicado: (1999)

Fluid draughting media: requirements and test conditions
por: International Organization for Standardization. Geneva
Publicado: (1997)

Technical drawings: draughting media and tools for vector plotters
por: International Organization for Standardization. Geneva
Publicado: (1999)

Process measurement control functions and instrumentation : symbolic representation: part 1 : basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1977)

Specification for diagrams for process industry: part 1 : general rules
por: International Organization for Standardization. Geneva
Publicado: (1975)

Process measurement control functions and instrumentation : symbolic representation: part 3 : detailed symbols for instrument interconnection diagrams
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Process measurement control functions and instrumentation : symbolic representation: part 2 : extension of basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Optics and optical instruments - preparation of drawings for opticalelements and systems: Part 6 : centring tolerances
por: International Organization for Standardization. Geneva
Publicado: (1996)

Optics and optical instruments - preparation of drawings for opticalelements and systems: Part 11 : non-toleranced data
por: International Organization for Standardization. Geneva
Publicado: (1996)

Construction drawings: Part 1 : Buildings and parts of buildings
por: International Organization for Standardization. Geneva
Publicado: (1998)

Technical drawings: Part 1 : Graphical symbols for plumbing, heating, ventilation and ducting
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Pipe threads where pressure-tight joints are made on the threads: part 1 : dimensions, tolerances and designation
por: International Organization for Standardization. Geneva, et al.
Publicado: (1994)

Technical drawings - screw threads and threaded parts: Part 1 : general conventions
por: International Organization for Standardization. Geneva
Publicado: (1993)

Flow diagrams for process plants - general rules
por: International Organization for Standardization. Geneva
Publicado: (1997)

Technical drawings: Scales
por: International Organization for Standardization. Geneva, et al.
Publicado: (1979)

Building and civil engineering drawings : installations: part 2 : simplified representation of sanitary appliances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1980)

Technical drawings : installations: part 6 : graphical symbols for supply water and drainage systems in the ground
por: International Organization for Standardization. Geneva, et al.
Publicado: (1985)

Technical drawings - screw threads and threaded parts: Part 2 : screw thread inserts
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - simplified representation of the assembly of parts with fasteners: Part 2 : rivets for aerospace equipment
por: International Organization for Standardization. Geneva
Publicado: (1995)

Microfilming of technical drawings and other drawing office documents: Part 1 : Operating procedures
por: International Organization for Standardization. Geneva
Publicado: (1983)

Technical product documentation - handling of computer-based technical information: Part 1 : security requirements
por: International Organization for Standardization. Geneva
Publicado: (1993)

Draughts and Deaths
por: Chambers, William
Publicado: (1893)

Technical product documentation: Part 3 : Greek alphabet
por: International Organization for Standardization. Geneva
Publicado: (2000)

Technical product documentation - springs: Part 3 : vocabulary
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings : simplified representation of moulded, cast and forged parts
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - projection methods: Part 3 : axonometric representations
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical product documentation: Part 2 : Latin alphabet, numerals and marks
por: International Organization for Standardization. Geneva
Publicado: (2000)

Technical drawings - rolling bearings: Part 2 : detailed simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - general principles of presentation: Part 20 : basic conventions for lines
por: International Organization for Standardization. Geneva
Publicado: (1996)

Cannot write session to /tmp/vufind_sessions/sess_pn6o46336q3cbnu0ad3ijg9lkm