Cargando…

Technical drawings - screw threads and threaded parts: Part 3 : simplified representation

Detalles Bibliográficos
Autor principal:	International Organization for Standardization. Geneva
Lenguaje:	eng
Publicado:	ISO 1993
Materias:	Engineering
Acceso en línea:	http://cds.cern.ch/record/500811

Ejemplares similares

Technical drawings - screw threads and threaded parts: Part 2 : screw thread inserts
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - screw threads and threaded parts: Part 1 : general conventions
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - simplified representation of the assembly of parts with fasteners: Part 1 : general principles
por: International Organization for Standardization. Geneva
Publicado: (1995)

Technical drawings - simplified representation of pipelines: Part 2 : isometric projection
por: International Organization for Standardization. Geneva
Publicado: (1989)

Technical drawings - rolling bearings: Part 1 : general simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1989)

Technical drawings - simplified representation of pipelines: Part 1 : general rules and orthogonal representation
por: International Organization for Standardization. Geneva
Publicado: (1989)

Technical drawings - seals for dynamic application: Part 1 : general simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1989)

Technical drawings - seals for dynamic application: Part 2 : detailed simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1989)

Technical drawings - simplified representation of pipelines: Part 3 : terminal features of ventilation and drainage systems
por: International Organization for Standardization. Geneva
Publicado: (1993)

Fasteners and screw threads
por: International Organization for Standardization. Geneva
Publicado: (1991)

Technical drawings - construction drawings - simplified representation of demolition and rebuilding
por: International Organization for Standardization. Geneva
Publicado: (1983)

Technical drawings - simplified representation of centre holes
por: International Organization for Standardization. Geneva
Publicado: (1982)

Technical drawings : simplified representation of moulded, cast and forged parts
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - projection methods: Part 2 : orthographic representations
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings - simplified representation of bars and profile sections
por: International Organization for Standardization. Geneva
Publicado: (1995)

Technical product documentation - springs: Part 1 : simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - rolling bearings: Part 2 : detailed simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - simplified representation of the assembly of parts with fasteners: Part 2 : rivets for aerospace equipment
por: International Organization for Standardization. Geneva
Publicado: (1995)

Technical product documentation - Vocabulary - Part 1: terms relating to technical drawings: general and types of drawings
por: International Organization for Standardization. Geneva, et al.
Publicado: (1992)

Technical drawings - projection methods: Part 4: central projection
por: International Organization for Standardization. Geneva, et al.
Publicado: (1998)

Pipe threads where pressure-tight joints are made on the threads: part 1 : dimensions, tolerances and designation
por: International Organization for Standardization. Geneva, et al.
Publicado: (1994)

Technical drawings - projection methods: Part 1 : synopsis
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings - general principles of presentation: Part 23: lines on construction drawings
por: International Organization for Standardization. Geneva
Publicado: (1999)

Technical drawings - projection methods: Part 3 : axonometric representations
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings: general principles of presentation : part 24 : lines on mechanical engineering drawings
por: International Organization for Standardization. Geneva
Publicado: (1999)

Technical drawings - general principles of presentation: Part 34: views on mechanical engineering drawings
por: International Organization for Standardization. Geneva
Publicado: (2001)

Technical drawings - general principles of presentation: Part 44: sections on mechanical engineering drawings
por: International Organization for Standardization. Geneva
Publicado: (2001)

Construction drawings - simplified representation of concrete reinforcement
por: International Organization for Standardization. Geneva
Publicado: (1995)

Technical drawings: Conventional representation of gears
por: International Organization for Standardization. Geneva
Publicado: (1973)

Technical drawings - representation of splines and serrations
por: International Organization for Standardization. Geneva
Publicado: (1988)

Technical drawings - construction drawings - representation of views, sections and cuts
por: International Organization for Standardization. Geneva
Publicado: (1984)

Building and civil engineering drawings : installations: part 2 : simplified representation of sanitary appliances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1980)

Technical drawings - construction drawings - representation of modular sizes, lines and grids
por: International Organization for Standardization. Geneva
Publicado: (1986)

Technical drawings - general principles of presentation: Part 30: basic conventions for views
por: International Organization for Standardization. Geneva
Publicado: (2001)

Technical drawings - lettering: Part 4 : diacritical and particular marks for the Latin alphabet
por: International Organization for Standardization. Geneva
Publicado: (2000)

Construction drawings: Part 3: room identifiers
por: International Organization for Standardization. Geneva
Publicado: (1998)

Technical drawings - general principles of presentation: Part 40: basic conventions for cuts and sections
por: International Organization for Standardization. Geneva
Publicado: (2001)

Microfilming of technical drawings and other drawing office documents: Part 5: test procedures for diazo duplicating of microfilm images in aperture cards
por: International Organization for Standardization. Geneva
Publicado: (1999)

Microfilming of technical drawings and other drawing office documents: Part 2 : quality criteria and control of 35 mm silver gelatin microfilms
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings - general principles of presentation: Part 50: basic conventions for representing areas on cuts and sections
por: International Organization for Standardization. Geneva
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_t94mh71f8vgj7f5konhkda1fev