Cargando…

APS SR Flexible Bellows Shield Performance

Detalles Bibliográficos
Autores principales:	Jones, J, Sharma, S, Bromberek, D, Howell, J
Lenguaje:	eng
Publicado:	1999
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/552776

Ejemplares similares

The vacuum bellows and the optimization of their shielding
por: Unterlerchner, W, et al.
Publicado: (1986)

Broad-band impedance of LHC shielded bellows
por: Dyachkov, M, et al.
Publicado: (1998)

Observation and calculation of trapped modes near cut-off in the ALS bellows-shield
por: Corlett, J N
Publicado: (1996)

Impedance of bellows corrugations
por: Ng, K Y
Publicado: (1987)

Impedances Of RF Bellows
por: Henke, H
Publicado: (1983)

LHC Bellows Impedance Calculations
por: Dyachkov, M, et al.
Publicado: (1997)

Technical specification for flexible metal bellows (compensators) for the vacuum system of the 400 GeV proton accelerator
por: Wahl, H
Publicado: (1977)

Technical specification for flexible metal bellows (compensators) for the vacuum system of the 400 GeV proton accelerator
por: CERN. Geneva
Publicado: (1980)

Specification for bellows to be used in HT vacuum relay
por: Hoekemeijer, F
Publicado: (1979)

Fatigue Life Prediction for Finite Ratcheting of Bellows at Cryogenic Temperatures
por: Skoczen, Blazej, et al.
Publicado: (1995)

Mechanical stability of piping systems equipped with bellows expansion
por: Skoczen, Blazej, et al.
Publicado: (1997)

Longitudinal and transverse impedances of bellows in the low frequency range
por: Kheifets, S A, et al.
Publicado: (1986)

Current limitations in LEP due to vacuum chamber bellows
por: Zotter, Bruno W
Publicado: (1985)

Short specification for welded bellows for mechanisms of the antiproton accumulator
Publicado: (1979)

Mechanical Design of a Flexible Bunch Compressor for APS Linac
por: Rotela, E R, et al.
Publicado: (2001)

Failure Mechanism and Consolidation of the Compensation Bellows of the LHC Cryogenic Distribution Line
por: Brodzinski, K, et al.
Publicado: (2015)

Influence of Micro-Damage on Reliability of Cryogenic Bellows in the LHC Interconnections
por: Garion, C, et al.
Publicado: (2008)

Long, Bellows-Free Vertical Helium Transfer Lines for the LHC Cryogenic System
por: Gruehagen, Henning, et al.
Publicado: (2002)

Flexible metal bellows
por: CERN. Geneva. Super Proton Synchrotron Division (SPS)
Publicado: (1974)

Energy loss in the tapers and bellows of the LEP super conducting cavity modules
por: Zotter, Bruno W
Publicado: (1992)

Specification for the manufacture of high frequency finger contacts for the vacuum-bellow systems
por: CERN. Geneva
Publicado: (1987)

Short specification for bellows for the RF wave guides of the LEP injector linac
Publicado: (1983)

Short specification for bellows for the RF wave guides of the LEP injector Linac
Publicado: (1983)

Technical specification for the supply of standard and enlarged size bellows for the PS machine
Publicado: (1985)

Technical specification for the supply of standard and enlarged size bellows for the PS machine
Publicado: (1985)

Technical specification for the manufacture of the metal transitions (bellows) for the CERN Antiproton Collector
Publicado: (1984)

Specification for the flexible metal bellows, transition pieces and flanges for the vacuun tubes for magnets in the West Experimental Area of the 300 GeV proton synchroton
por: Pearce, N
Publicado: (1974)

Specification for the flexible metal bellows, transition pieces, and flanges for the vacuum tubes for magnets in the West experimental area of the 300 GeV proton synchrotron
Publicado: (1974)

Flexible metal bellows
por: CERN PhotoLab
Publicado: (1975)

Flexible and Telescopic Vacuum Chambers for the APS Bunch Compressor
por: Walters, D R, et al.
Publicado: (2001)

Characterization of the RF Fingers Contact Force for the LHC Warm Vacuum Bellow Modules
por: Blanch Gutiérrez, Cesar, et al.
Publicado: (2015)

Technical specification for the flexible metal bellows (compensators) and transition pieces for the vacuum chamber of the 300 GeV proton accelerator: Invitation to tender III-21-22-ME
por: CERN. Geneva
Publicado: (1972)

Specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges, and vacuum tubes for the magnets in the Experimental Areas of the 450 GeV Proton Synchrotron
por: CERN. Geneva
Publicado: (1982)

IMPASS: a computer program for calculations of impedances of periodic axially symmetric smooth structures (bellows)
por: Kheifets, S A, et al.
Publicado: (1985)

Effect of Shear Deformation and Relaxation of Support Conditions on Buckling of Pressurized Pipelines containing Expansion Bellows
por: Skoczen, Blazej
Publicado: (1998)

Technical questionnaire for the supply of standard and enlarged size bellows for the PS machine. (To be completed and signed by the tenderer)
Publicado: (2023)

Technical specification for supply of ∅140 and ∅150 mm bellows (For subsequent incorporation into quadrupole vacuum vessels)
Publicado: (1984)

Impedance measurements of rf joint (bellows shield) for collider
por: Walling, L, et al.
Publicado: (1994)

Specification for the manufacture of mechanical components for the vacuum-bellow systems - 1st revision 25/9/87
por: CERN. Geneva
Publicado: (1987)

Technical specification for the vacuum chamber assemblies comprising flexible metal bellows, transition pieces, flanges and vacuum tubes for the magnets MCA/MCB in the experimental areas of the 450 GeV proton synchrotron
por: CERN. Geneva
Publicado: (1988)

Cannot write session to /tmp/vufind_sessions/sess_ftj53hfjqq7qfancn1pv95cqta