Cargando…

Hexagon nuts for structural bolting with large width across flats, style 1: Property class 10

Detalles Bibliográficos
Autor principal:	International Organization for Standardization. Geneva
Lenguaje:	eng
Publicado:	ISO 1984
Materias:	Information Transfer and Management
Acceso en línea:	http://cds.cern.ch/record/572425

Ejemplares similares

Hexagon bolts for high-strength structural bolting with large width across flats (short thread length): Property classes 8.8 and 10.9
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Hexagon nuts for structural bolting: Property class 9
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Hexagon bolts for high-strength structural bolting with large width across flats (thread lengths according to 888): Property classes 8.8 and 10.9
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize tapped): Property classes 5, 6 and 8
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Bolts, screws, nuts and accessories: Terminology and nomenclature
por: International Organization for Standardization. Geneva, et al.
Publicado: (1979)

Slotted countersunk (flat) head tapping screws (common head style)
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Hexagon head tapping screws
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Plain washers for high-strength structural bolting, hardened and tempered
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Bolts, screws and studs: Nominal lengths, and thread lengths for general purpose bolts
por: International Organization for Standardization. Geneva
Publicado: (1976)

Cross recessed countersunk (flat) head tapping screws (common head style)
por: International Organization for Standardization. Geneva
Publicado: (1983)

Slotted raised countersunk (oval) head tapping screws (common head style)
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Process measurement control functions and instrumentation : symbolic representation: part 2 : extension of basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Process measurement control functions and instrumentation : symbolic representation: part 3 : detailed symbols for instrument interconnection diagrams
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Technical drawings: Part 1 : Graphical symbols for plumbing, heating, ventilation and ducting
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Sintered metal materials, excluding hardmetals: Determination of transverse rupture strength
por: International Organization for Standardization. Geneva, et al.
Publicado: (1996)

Hydraulic fluid power: filter elements : verification of material compatibility with fluids
por: International Organization for Standardization. Geneva, et al.
Publicado: (1998)

Liquid flow measurement in open channels: Rectangular, trapezoidal and U-shaped flumes
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Data elements and interchange formats: information interchange : representation of dates and times
por: International Organization for Standardization. Geneva, et al.
Publicado: (2004)

Process measurement control functions and instrumentation : symbolic representation: part 1 : basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1977)

Technical drawings : installations: part 6 : graphical symbols for supply water and drainage systems in the ground
por: International Organization for Standardization. Geneva, et al.
Publicado: (1985)

Technical drawings: Scales
por: International Organization for Standardization. Geneva, et al.
Publicado: (1979)

Building and civil engineering drawings : installations: part 2 : simplified representation of sanitary appliances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1980)

Slotted pan head tapping screws
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Rubber and plastics hoses and hose assemblies: Ratios of proof and burst pressure to design working pressure
por: International Organization for Standardization. Geneva, et al.
Publicado: (1991)

Technical drawings: Datums and datum-systems for geometrical tolerances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1981)

Geometrical Product Specifications (GPS): series of angles and slopes on prisms
por: International Organization for Standardization. Geneva, et al.
Publicado: (1998)

Pipe threads where pressure-tight joints are made on the threads: part 1 : dimensions, tolerances and designation
por: International Organization for Standardization. Geneva, et al.
Publicado: (1994)

Technical drawings: Maximum material principle
por: International Organization for Standardization. Geneva, et al.
Publicado: (1988)

Cinematography
por: International Organization for Standardization. Geneva
Publicado: (1984)

Paper, board and pulps
por: International Organization for Standardization. Geneva
Publicado: (1984)

Technical drawings : simplified representation of moulded, cast and forged parts
por: International Organization for Standardization. Geneva
Publicado: (1994)

Specification for diagrams for process industry: part 1 : general rules
por: International Organization for Standardization. Geneva
Publicado: (1975)

Microfilming of technical drawings and other drawing office documents: Part 1 : Operating procedures
por: International Organization for Standardization. Geneva
Publicado: (1983)

Technical product documentation: Part 2 : Latin alphabet, numerals and marks
por: International Organization for Standardization. Geneva
Publicado: (2000)

Technical product documentation: Part 3 : Greek alphabet
por: International Organization for Standardization. Geneva
Publicado: (2000)

Technical drawings: Cones
por: International Organization for Standardization. Geneva
Publicado: (1990)

Technical drawings: Fundamental tolerancing principle
por: International Organization for Standardization. Geneva
Publicado: (1985)

Normalisation et documentation: introduction pour documentalistes et bibliothecaires
por: International Organization for Standardization. Geneva
Publicado: (1983)

Standardization and documentation: an introduction for documentalists and librarians
por: International Organization for Standardization. Geneva
Publicado: (1983)

Information transfer
por: International Organization for Standardization. Geneva
Publicado: (1982)

Cannot write session to /tmp/vufind_sessions/sess_5183fdc567o3havkojfiud2qb7