Cargando…

Pipe threads where pressure-tight joints are made on the threads: part 1 : dimensions, tolerances and designation

Detalles Bibliográficos
Autor principal:	International Organization for Standardization. Geneva
Lenguaje:	eng
Publicado:	ISO 1994
Materias:	Information Transfer and Management
Acceso en línea:	http://cds.cern.ch/record/576468

Ejemplares similares

Technical drawings - screw threads and threaded parts: Part 2 : screw thread inserts
por: International Organization for Standardization. Geneva
Publicado: (1993)

Technical drawings - screw threads and threaded parts: Part 1 : general conventions
por: International Organization for Standardization. Geneva
Publicado: (1993)

Bolts, screws and studs: Nominal lengths, and thread lengths for general purpose bolts
por: International Organization for Standardization. Geneva
Publicado: (1976)

Hexagon bolts for high-strength structural bolting with large width across flats (short thread length): Property classes 8.8 and 10.9
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Hexagon bolts for high-strength structural bolting with large width across flats (thread lengths according to 888): Property classes 8.8 and 10.9
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Technical drawings - screw threads and threaded parts: Part 3 : simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1993)

Manually operated draughting machines: Part 3 : dimensions of scale rule chuck plates
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings: Datums and datum-systems for geometrical tolerances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1981)

Technical drawings: Part 1 : Graphical symbols for plumbing, heating, ventilation and ducting
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Process measurement control functions and instrumentation : symbolic representation: part 1 : basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1977)

Building and civil engineering drawings : installations: part 2 : simplified representation of sanitary appliances
por: International Organization for Standardization. Geneva, et al.
Publicado: (1980)

Process measurement control functions and instrumentation : symbolic representation: part 2 : extension of basic requirements
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Technical drawings : installations: part 6 : graphical symbols for supply water and drainage systems in the ground
por: International Organization for Standardization. Geneva, et al.
Publicado: (1985)

Process measurement control functions and instrumentation : symbolic representation: part 3 : detailed symbols for instrument interconnection diagrams
por: International Organization for Standardization. Geneva, et al.
Publicado: (1984)

Optics and optical instruments - preparation of drawings for opticalelements and systems: Part 6 : centring tolerances
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical drawings: Dimensioning and tolerancing of profiles
por: International Organization for Standardization. Geneva
Publicado: (1987)

Technical drawings: Tolerancing of linear and angular dimensions
por: International Organization for Standardization. Geneva
Publicado: (1987)

Construction drawings: Part 1 : Buildings and parts of buildings
por: International Organization for Standardization. Geneva
Publicado: (1998)

Technical drawings - simplified representation of the assembly of parts with fasteners: Part 2 : rivets for aerospace equipment
por: International Organization for Standardization. Geneva
Publicado: (1995)

Fasteners and screw threads
por: International Organization for Standardization. Geneva
Publicado: (1991)

Technical product documentation: Part 3 : Greek alphabet
por: International Organization for Standardization. Geneva
Publicado: (2000)

Technical product documentation - springs: Part 3 : vocabulary
por: International Organization for Standardization. Geneva
Publicado: (1993)

Draughting instruments with or without graduation: Part 2 : protractors
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical drawings : simplified representation of moulded, cast and forged parts
por: International Organization for Standardization. Geneva
Publicado: (1994)

Specification for diagrams for process industry: part 1 : general rules
por: International Organization for Standardization. Geneva
Publicado: (1975)

Technical drawings - projection methods: Part 3 : axonometric representations
por: International Organization for Standardization. Geneva
Publicado: (1996)

Draughting instruments with or without graduation: Part 3 : set squares
por: International Organization for Standardization. Geneva
Publicado: (1994)

Technical product documentation: Part 2 : Latin alphabet, numerals and marks
por: International Organization for Standardization. Geneva
Publicado: (2000)

Technical drawings - rolling bearings: Part 2 : detailed simplified representation
por: International Organization for Standardization. Geneva
Publicado: (1994)

Draughting instruments with or without graduation: Part 1 : draughting scale rules
por: International Organization for Standardization. Geneva
Publicado: (1992)

Manually operated draughting machines: Part 1 : definitions, classification and designation
por: International Organization for Standardization. Geneva
Publicado: (1992)

Technical drawings - general principles of presentation: Part 20 : basic conventions for lines
por: International Organization for Standardization. Geneva
Publicado: (1996)

Technical product documentation - vocabulary: Part 2 : terms relating to projection methods
por: International Organization for Standardization. Geneva
Publicado: (1993)

Mechanical pencils: Part 3 : black leads - bending strengths of HB leads
por: International Organization for Standardization. Geneva
Publicado: (1994)

Manually operated draughting machines: Part 2 : characteristics, performance, inspection and marking
por: International Organization for Standardization. Geneva
Publicado: (1992)

Sintered metal materials, excluding hardmetals: Determination of transverse rupture strength
por: International Organization for Standardization. Geneva, et al.
Publicado: (1996)

Hydraulic fluid power: filter elements : verification of material compatibility with fluids
por: International Organization for Standardization. Geneva, et al.
Publicado: (1998)

Liquid flow measurement in open channels: Rectangular, trapezoidal and U-shaped flumes
por: International Organization for Standardization. Geneva, et al.
Publicado: (1983)

Data elements and interchange formats: information interchange : representation of dates and times
por: International Organization for Standardization. Geneva, et al.
Publicado: (2004)

Technical drawings: Scales
por: International Organization for Standardization. Geneva, et al.
Publicado: (1979)

Cannot write session to /tmp/vufind_sessions/sess_fdtckga7ealf0kk13aahnuiddk