Cargando…

CB-2 ready for impregnation

CB-2 is ready for impregnation.

Detalles Bibliográficos
Autor principal:	P. Fabbricatore
Lenguaje:	ENG
Publicado:	2003
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/615902

Ejemplares similares

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Coupling of CB-2 and CB-1
por: Ansaldo
Publicado: (2003)

Last layer of CB-2
por: Ansaldo
Publicado: (2003)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

Insertion of prototype in impregnation autoclave
por: Ansaldo
Publicado: (2002)

Situation of CB+1/CB+2 mid January 2004
por: Ansaldo
Publicado: (2004)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

Impregnation chamber close with prototype inside
por: Ansalso
Publicado: (2002)

Winding Prototype has been impregnated.
por: Ansaldo
Publicado: (2002)

Construction of mandrel CB-2
por: Ansaldo
Publicado: (2002)

Loading CB-2 on board
por: Ansaldo
Publicado: (2004)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Preparation for vacuum epoxy impregnation
por: M.Perrella
Publicado: (2000)

CB0 wound
por: Ansaldo
Publicado: (2004)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Cross section of the impregnated model coil
por: M.Perrella
Publicado: (2000)

Model coil extracted from impregnation mold
por: M.Perrella
Publicado: (2000)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

YE-2 ready for photogrammetry survey.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Elements of the winding machine at TPA.
por: P. Fabbricatore
Publicado: (2001)

First bending test at TPA using full section dummy conductor
por: P. Fabbricatore
Publicado: (2001)

Manufacture of the winding prototype mandrel at San Giorgio.
por: P. Fabbricatore
Publicado: (2001)

View of the winding machine with real conductor.
por: Pasquale Fabbricatore
Publicado: (2001)

Preparation of winding prototype at S. Giorgio Siegen.
por: Pasquale Fabbricatore
Publicado: (2001)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

First turns of insulated conductor at S. Giorgio inside the winding prototype mandrel.
por: Pasquale Fabbricatore
Publicado: (2001)

Big Barrel Yoke block after painting, ready for transport, weight 40 t
por: Franz Leher, DWE, et al.
Publicado: (2000)

October, 25th, 2000 First Barrel Ring with extension shaft ready for separation
por: Hubert Gerwig
Publicado: (2000)

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

View of muon cable trays on YE+2
por: Lucien Veillet
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_bihar05juma1ocu92h3rj0mrdo