Cargando…

Assembly of the CMS Solenoid Inner Thermal Shield

Assembly of the CMS solenoid inner thermal shield. Assembly, pipe welding, thermal shock. Work performed by Criotec.

Detalles Bibliográficos
Autor principal:	Bruno LEVESY
Publicado:	2004
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/709472

Ejemplares similares

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Delivery of the 5 modules of the CMS Solenoid
por: Bruno LEVESY
Publicado: (2004)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

The CMS solenoid goes down to 100 Kelvin (-170 degrees Celsius)
por: Marc Favre, CERN
Publicado: (2006)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

EBW line assembly status for CMS conductor
por: Techmeta
Publicado: (2000)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

CMS coil thermal shields final design
por: Fazilleau, P, et al.
Publicado: (2002)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

CMS Swiveling Platform for Coil and Inner Vacuum Tank Static Load Test 350 t performed at Dong Yang (South Korea) 2001-08-21 to 23
por: Alain PAYN
Publicado: (2001)

Inner vacuum tank in SX5
por: Pascal Petiot
Publicado: (2002)

Machining of inner vacuum tank rails
por: Hubert Gerwig
Publicado: (2001)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

View of inner and outer vacuum tanks
por: Maximilien Brice
Publicado: (2003)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Swiveling of inner vacuum tank to vertical position
por: P. Petiot
Publicado: (2002)

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Full cross section of CMS conductor
por: Stefano Sgobba
Publicado: (2001)

CMS delegation for MTB55 held at Tata Institute in Mumbai (Bombay) during CMS week 14 December 2000.
por: A. Payn
Publicado: (2000)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_j1ak568o369sb6uipmjlieh5bs