Cargando…

HE+1 through vactank

HE+1 seen through vactank

Detalles Bibliográficos
Autor principal:	Veillet
Publicado:	2003
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/710610

Ejemplares similares

Trial insertion of inner vactank inside outer vactank.
por: Maximilien Brice
Publicado: (2002)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Final stage of inner vactank machining
por: Hubert Gerwig
Publicado: (2001)

Measure by photogrammetry of outer vactank cylindricity after adjunction of the reinforcement rings.
por: Céline Humbertclaude
Publicado: (2001)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

CMS - VACTANK CYLINDRICITY
por: Raphael GOUDARD, et al.
Publicado: (2002)

The outer vactank, an object of 7.6m diameter and 13m length is built up of three cylindrical parts. The central part that is integral part of the central barrel and the the extension on either side each one 4.5m long. These extensions house the shoulders that will support and prestress the CMS Coil. To weld the extensions onto the central part a full penetration weld of 24m length and 45 mm thickness has to be done by hand from inside and outside the vacuum tank and its deformation is controled permanently.
por: Hubert Gerwig
Publicado: (2001)

View of muon cable trays on YE+2
por: Lucien Veillet
Publicado: (2003)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

View of SX hall beginning of March 2002.
por: Lucien Veillet
Publicado: (2002)

Preparation for welding of the outer vacuum tank
por: L. Veillet
Publicado: (2001)

First connecting pieces between yoke elements.
por: Lucien Veillet
Publicado: (2001)

Arrival of Cold Box
por: L. Veillet
Publicado: (2002)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Drilling of pins for retaining frames in SX5
por: L. Veillet
Publicado: (2002)

Fixation of stabilizing cylinders on YE+2
por: Lucien Veillet
Publicado: (2002)

Fixation of stabilizing tubes on Endcap disks
por: Lucien Veillet
Publicado: (2002)

Z stop on YE+2
por: Lucien Veillet
Publicado: (2002)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Inner Vactank on the swilling platform, YB-2
por: Jean-Frederic FUCHS, et al.
Publicado: (2003)

Tracker VacTank Equipment Documentation Photos
por: Hoch, Michael
Publicado: (2009)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

View of 1st Barrel Wheel in SX5 (1st layer plus corner pieces)
por: J.P. Grillet
Publicado: (2000)

Coupling of CB-2 and CB-1
por: Ansaldo
Publicado: (2003)

YB-1 barrel yoke photogrametry on the ferryswheel
por: petiot Pascal
Publicado: (2000)

YE-1 disks in KHI, Kobe, Japan
por: F. Feyzi
Publicado: (2000)

Taking photogrammetric measurements of first YE1 at KHI.
por: C. Humbertclaude
Publicado: (2000)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Arrival of 1st Pakistani feet in DX5
por: J.P. Grillet
Publicado: (2000)

View of the photogrammetric targets for the first YE1 at KHI.
por: C. Humbertclaude
Publicado: (2000)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_li9i8kihfnvq9s727v2tvqpq2e