Cargando…

LHCb Magnet assembly status

LHCb Magnet assembly status

Detalles Bibliográficos
Autor principal:	Koppenburg, P
Publicado:	2004
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/726999

Ejemplares similares

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

First plate of LHCb Magnet Yoke in place
por: Lindner, R.
Publicado: (2003)

EBW line assembly status for CMS conductor
por: Techmeta
Publicado: (2000)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Assembly of YE-1
por: Lucien Veillet
Publicado: (2001)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

Assembly of minus endcap finished
por: Dick Loveless, et al.
Publicado: (2001)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

YB0 central barrel assembly
por: Pascal Petiot
Publicado: (2001)

Assembly of the first sectors of YE-2
por: F. Feyzi
Publicado: (2001)

Assembly of Endcap started at SX5
por: Farshid Feyzi
Publicado: (2001)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

Assembly of YE-2 finished at SX5
por: Dick Loveless, et al.
Publicado: (2001)

Assembly of Ferryswheel in SX5 ,Pt.5.
por: Pascal Petiot
Publicado: (2000)

Half-disk assembly of YE-2 at Kawasaki.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Explosion cases of EBW assembly of conductor N°1
por: Pascal Petiot
Publicado: (2001)

Magnet yoke pieces
por: Pascal Petiot
Publicado: (2000)

Endcap support cart assembly finished Carts YE-3, YE-2, YE-1, Y+1, YE+2 compleleted assemblies shown in an overhead photo Several Subassemblies are also shown
por: Farshid Feyzi, et al.
Publicado: (2001)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Assembly of the CMS Yoke. On the lifting device you can see a block for the third layer
por: DWE Werksfoto Nr: 6.46305.528
Publicado: (1999)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.
por: B. CURE
Publicado: (2004)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

CMS CONDUCTOR EBW PRODUCTION LINE AT TECHMETA - STATUS OF THE 17.01.01
por: Ramon Folch
Publicado: (2001)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

CERN survey team at KHI for photogrammetry of magnetic endcaps.Raphaël Goudard (CERN), Farshid Feyzi (from PSL) and Céline Humbertclaude (CERN) with KHI engineers.
por: R. Loveless/U. of Wisconsin
Publicado: (2000)

Sliding operation for CMS Inner Vacuum Tank from it's swivelling platform to the storage platform
por: P.Petiot
Publicado: (2004)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

Cannot write session to /tmp/vufind_sessions/sess_ns74jul0sgifkgvuk6sjkee86d