Cargando…

Front-end chip cable and jif on Delvotec (bonding machine)

Front-end chip cable and jif on Delvotec (bonding machine).

Detalles Bibliográficos
Autor principal:	Alessandro, B.
Publicado:	2004
Materias:	ITS
Acceso en línea:	http://cds.cern.ch/record/779689

Ejemplares similares

Chip cables aligned on hybrid on assembly jig
por: Alessandro, B.
Publicado: (2004)

In the photograph, one can see the interconnection from one readout chip to the flexible cable realized with ultrasonic wire bonds (25 microns).
por: Saba, A
Publicado: (2006)

The board with the front-end ASIC's called PASCAL and AMBRA (part of readout setup)
por: Alessandro, B.
Publicado: (2004)

The read-out electronics boards contain ASICs (ALABUF and ALCAPONE) to condition and buffer the analog signals and to control the front-end chips (HAL25).
por: Nooren, G.
Publicado: (2004)

SEM picture of bump bonding pads on ALICE readout chip
Publicado: (2002)

Wire bonding of the MCM multi chip module using 25 micron wire at CERN.
por: Saba, A
Publicado: (2006)

ALICE Pixel Ladder (5 chips bump bonded to 1 sensor) mounted on prototype bus
Publicado: (2002)

ALICE Testbeam 2002-Reference plane made of 2 bump bonded single chip assemblies
Publicado: (2002)

Alice Silicon Strip Detector, HAL cable
por: xxx, x
Publicado: (2007)

Hybrid bonding on K&S manual bonder
por: Alessandro, B.
Publicado: (2004)

Alice Silicon Strip Detector, preparation of ladder cable
por: xxx, x
Publicado: (2006)

A silicon Drift Detector and its two fronted boards
por: Nouais, D.
Publicado: (2004)

Probing of ALICE single chip assembly
Publicado: (2001)

Alice Silicon Strip Detector, chip
por: xxx, x
Publicado: (1999)

ALICE pixel prototype bus with 10 readout chips
Publicado: (2002)

ALICE pixel readout chip with 8192 readout channels
Publicado: (2001)

Wire bonding work at CERN
Publicado: (2006)

ALICE ladder mounted and wire bonded on prototype bus
Publicado: (2002)

Alice Silicon Strip Detector, HAL bonding tool
por: xxx, x
Publicado: (2002)

Particular of the set up for testing the cooling system of SDD
por: Alessandro, B.
Publicado: (2004)

Set up to test the cooling system of SDD
por: Alessandro, B.
Publicado: (2004)

The DAQ screen during the test of the readout of SDD
por: Alessandro, B.
Publicado: (2004)

Set up to test the redout chain of SDD
por: Alessandro, B.
Publicado: (2004)

The board with the compression ASIC called CARLOS (part of readout setup)
por: Alessandro, B.
Publicado: (2004)

Completed hybrid
por: Alessandro, B.
Publicado: (2004)

Full-scale model of the ALICE ITS Detector
Publicado: (2004)

Multiple trigger scintillators were installed: big ones covering the total surface of the sensor and several smaller ones. The former give a trigger for each beam particle. The latter are used to select a part of the sensor surface for efficiency measurements.
por: Nooren, G.
Publicado: (2004)

In ALICE particles will hit the sensors at oblique angles. This is partly simulated here by rotating the modules.
por: Nooren, G.
Publicado: (2004)

Installation of the light tight cover for the SSD modules (the modules are behind the aluminium plate). The silicon sensors are sensitive to light tight, so ambient light will increase the noise and may even damage them.
por: Nooren, G.
Publicado: (2004)

The T10 beam produces a few hits per event. In ALICE the SSD will have to cope with many hits per strip. In the three centimeters of aluminium the beam will produce many secondary particles. This increases the chance of multiple hits per strip, although not to the level in ALICE.
por: Nooren, G.
Publicado: (2004)

Alice Silicon Strip Detector, thermodes
por: xxx, x
Publicado: (2004)

ALICE ITS
Publicado: (2003)

ALICE ITS Testbeam setup with 4 pixel reference planes
Publicado: (2002)

ALICE ITS
Publicado: (2003)

ALICE Carbon fibre sector support
Publicado: (2001)

ALICE ladder mounted on prototype bus
Publicado: (2002)

Working of the 1st supermodule of the the PHOS photon spectrometer which contains 3584 lead tungstate crystals. One crystal is 18 centimetre long and weighs some 750 grams. Photo: Antonio Saba. Photographer. www.antoniosaba.com
por: Saba, Antonio
Publicado: (2006)

Members of the ALICE Pixel team testing the second sector of the ALICE Silicon Pixel Detector in the divisional silicon facility laboratory at CERN
por: Saba, A
Publicado: (2006)

View of the control room at the CERN Divisional Silicon Facilty
por: Saba, A
Publicado: (2006)

Working of the 1st supermodule of the the PHOS photon spectrometer which contasins 3584 lead tungstate crystals. One crystal is 18 centimetre long and weighs some 750 grams.
por: Saba, A
Publicado: (2006)

Cannot write session to /tmp/vufind_sessions/sess_5f6qjoe5cldhasvoabsih94vgb