Cargando…

Installation at Point 5 of the dump resistors for the CMS magnet surface tests.

Unloading and installation by TELEMA of the dump resistors for the magnet tests on the platform outside SX5 building at Point 5.

Detalles Bibliográficos
Autor principal:	B. CURE
Publicado:	2004
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/793424

Ejemplares similares

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

The magnet and detector tests on point 5 surface come to an end. Pictures from the magnet and detector control rooms.
por: G. Perinic, et al.
Publicado: (2005)

Ultrasonic monitoring on the Electron Beam Welding line at Techmeta during manufacturing of the CMS magnet conductor.
por: Benoit CURE
Publicado: (2002)

Laser dimensional monitoring of the CMS magnet conductor, and associated printing system, during manufacturing on the Electron Beam Welding Line at Techmeta.
por: Benoit CURE
Publicado: (2002)

CMS conductor manufacturing at Techmeta by elecron beam welding
por: Benoit CURE
Publicado: (2001)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

Manufacture of grooves for installing magnetic measurement loops on YE-2
por: L. Veillet / EP
Publicado: (2001)

Manufacturing of the test cryostat. The test cryostat is used to simulate heat loads of the CMS magnet for the acceptance tests of the refrigeration system.
por: Goran Perinic
Publicado: (2002)

Installation of the intermediate cryostat.
por: Goran Perinic
Publicado: (2003)

Installation of diving boards
por: L. Veillet
Publicado: (2002)

Arrival of the cold box for the cryogenic refrigeration plant and installation in building SHL5.
por: Goran Perinic, et al.
Publicado: (2002)

Parts of CMS Magnet Barrel Yoke at PS.
Publicado: (2000)

Iron Blocks of CMS Magnet Barrel Yoke.
Publicado: (2000)

Cryogenic cold box during installation.
por: Goran Perinic
Publicado: (2003)

Helium transfer line installation details.
por: G. Perinic
Publicado: (2007)

Test ring of final CMS conductor for test ring in Marisa.
por: Pasquale Fabbricatore
Publicado: (2001)

Delivery of the 5 modules of the CMS Solenoid
por: Bruno LEVESY
Publicado: (2004)

Arrival of the vacuum tank inner shell for CMS supraconductive magnet.
por: Petiot Pascal
Publicado: (2001)

Design of a Compact Dump Resistor System for LCD Magnet
por: Gaddi, A, et al.
Publicado: (2010)

Installation of the liquid nitrogen tank for the external cryogenics system
Publicado: (2001)

Compressor station of the external cryogenic system during installation.
Publicado: (2002)

Installation of the LN2 tank in its final position.
por: G. Perinic
Publicado: (2007)

Load tests of swiveling tooling for the coil, held at CERN, point 5 on the 3rd of July, 2002.
por: Alain PAYN
Publicado: (2002)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Installation for connecting systems between barrels YB0/YB-1
por: Pascal Petiot
Publicado: (2001)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Installation of support disk of ME1/1 and first slice of HE-1
por: Lucien Veillet
Publicado: (2002)

first installation of one feet with the transport beam under YB-2 yoke barrel
por: petiot Pascal
Publicado: (2000)

Final dimensional test with alu-jig travelling through the CMS Inner vacuum tank
por: Hubert Gerwig
Publicado: (2001)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

Actual status of the magnet assembly in SX5 hall
por: P.Petiot
Publicado: (2001)

Start of Final Assembly of the CMS Barrel Yoke on schedule at P5 the 1st august, 2000. I
por: Hubert Gerwig, CERN/ EP-CMI
Publicado: (2000)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_d1vi1kda73a4blm2tpl22e835p