Cargando…

40 kA Superconducting DC Transformer for the FRESCA test station

This note presents the superconducting transformer that is now operated on the FRESCA test station. It is divided in two parts: part 1 from page 1 to 30 is the note itself, part 2 from page 31 to the end is annexes. After an introduction of the objectives and functioning of the superconducting trans...

Descripción completa

Detalles Bibliográficos
Autor principal:	Vincent-Viry, O
Lenguaje:	eng
Publicado:	2004
Materias:	Accelerators and Storage Rings
Acceso en línea:	http://cds.cern.ch/record/794618

Ejemplares similares

Conceptual Design of a new Sample Holder for the Fresca Cable Test Station
por: Bordini, B, et al.
Publicado: (2010)

13 kA Superconducting Busbars Manufacturing Process
por: Principe, R, et al.
Publicado: (2012)

The 40 kA dumping system for the ISR beams
por: Schnuriger, J C
Publicado: (1975)

Design, Assembly, and Commissioning of a Cryogenic DC Current Transformer Designed for Measuring Currents of up to 80 kA
por: Montenero, G, et al.
Publicado: (2015)

Quench Propagation in the Superconducting 6 kA Flexible Busbars of the LHC
por: Calvi, M, et al.
Publicado: (2001)

Consolidation of the 13-kA Superconducting Magnet Circuits of the LHC at CERN
por: Lackner, F, et al.
Publicado: (2015)

Quality Assurance of the 13-kA Superconducting Magnet Circuits Consolidation of the LHC at CERN
por: Principe, R, et al.
Publicado: (2016)

Analysis of Defective Interconnections of the 13 kA LHC Superconducting Bus Bars
por: Granieri, P P, et al.
Publicado: (2012)

Preparation and testing of prototype 12.5 kA high-temperature superconducting current leads for the LHC at CERN
por: Harrison, S, et al.
Publicado: (1996)

Pulsed D.C. power supply 16 kA. 60 V Schneider-Westinghouse
por: Schnetder, J.
Publicado: (1966)

Performance of the 1-m Model of the 6 kA Superconducting Quadrupole for the LHC Insertions
por: Lucas, J, et al.
Publicado: (2000)

Cryogenics of the 1.8 K test station for 10 Tesla superconducting magnet models
por: Haug, F, et al.
Publicado: (1988)

Performance of the single and twin-aperture models of the 6 kA superconducting quadrupole for the LHC insertions
por: Lucas, J, et al.
Publicado: (2001)

Design and Fabrication of FRESCA2 Cryostat
por: Dallocchio, Alessandro, et al.
Publicado: (2022)

CEA–CERN Block-Type Dipole Magnet for Cable Testing: FRESCA2
por: Rochepault, Etienne, et al.
Publicado: (2019)

Performance Improvement of a Measurement Station for Superconducting Cable Test
por: Arpaia, P, et al.
Publicado: (2012)

Test Station for Magnetization Measurements on Large Quantities of Superconducting Strands
por: Le Naour, S, et al.
Publicado: (2000)

Test Station for a 30 m long Superconducting Link
por: Benda, V, et al.
Publicado: (2007)

New Cryogenic Test Station at CERN for Superconducting Magnets and their Components
por: Bajko, M, et al.
Publicado: (2013)

Mechanical Validation of the Support Structure of the Magnet FRESCA2
por: Muñoz Garcia, J E, et al.
Publicado: (2015)

Critical current measurements of prototype cables for the CERN LHC up to 50 kA between 7 and 13 tesla using a superconducting transformer circuit*
por: ten Kate, H H J
Publicado: (1989)

Design optimization and evaluation of the 3 kA MgB$_2$ cable at 4.3 K for the superconducting link project at CERN
por: Konstantopoulou, K, et al.
Publicado: (2019)

Assembly, Loading, and Cool‐down of the FRESCA2 Support Structure
por: Muñoz Garcia, J E, et al.
Publicado: (2014)

Protection of the 13 T Nb$_{3}$Sn Fresca II dipole
por: Fazilleau, Ph., et al.
Publicado: (2014)

Assembly of the Nb$_{3}$Sn dipole magnet FRESCA2
por: Bourcey, Nicolas, et al.
Publicado: (2018)

Technical specification for two power supplies for superconducting magnet 6,4 kA, 60 V (power part)
Publicado: (1977)

A high-current, IGBT-based static switch for energy extraction in superconducting power circuits: Concept, design and production of a 30 kA monopolar and a 1 kA bipolar fast opening switches
por: Dahlerup-Petersen, K, et al.
Publicado: (2017)

Tests Results on the First 13 kA Prototype HTS Leads for the LHC
por: Ballarino, A, et al.
Publicado: (1999)

A 20 kA Test Bench for High-Precision Current Measurements
por: Dahlerup-Petersen, K, et al.
Publicado: (1999)

Fabrication and Assembly of the $Nb_3Sn$ Dipole Magnet FRESCA2
por: Rochepault, Etienne, et al.
Publicado: (2017)

18 kA vapour cooled current leads to test superconducting magnet models for the proposed Large Hadron Collider at CERN using wire matrix heat exchangers
por: Hagedorn, Dietrich, et al.
Publicado: (1988)

Upgrade of the CERN Cryogenic Station for Superfluid Helium Testing of Prototype LHC Superconducting Magnets
por: Benda, V, et al.
Publicado: (1997)

Consolidation of the 13 kA Splices in the Electrical Feedboxes of the LHC
por: Perin, A, et al.
Publicado: (2012)

10 kA Joints for HTS Roebel Cables
por: Murtomaki, Jaakko Samuel, et al.
Publicado: (2018)

Design of the EuCARD High-Field Model Dipole Magnet FRESCA2
por: Milanese, A, et al.
Publicado: (2012)

Development of the EuCARD Nb$_{3}$Sn Dipole Magnet FRESCA2
por: Ferracin, P, et al.
Publicado: (2013)

Mechanical Analysis of the FRESCA2 Dipole During Preload, Cool-Down, and Powering
por: Rochepault, Etienne, et al.
Publicado: (2018)

The novel 4kV, 40 kA capacitor discharge power converters for the pulsed septum magnets in the PS straight sections 16 and 58
por: Ducastel, C, et al.
Publicado: (1988)

Design and verification of a 24 kA calibration head for a DCCT test facility
por: Fernqvist, G, et al.
Publicado: (1998)

Thermal Runaway of the 13 kA Busbar Joints in the LHC
por: Verweij, A P
Publicado: (2010)

Cannot write session to /tmp/vufind_sessions/sess_cscf0efjn0u04iegh2000ggnak