Cargando…

CMS Solenoid module CB-1 before mounting of shield.

CMS solenoid coil module CB-1

Detalles Bibliográficos
Autor principal:	LEVESY
Publicado:	2005
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/837185

Ejemplares similares

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

Delivery of the 5 modules of the CMS Solenoid
por: Bruno LEVESY
Publicado: (2004)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

The CMS solenoid goes down to 100 Kelvin (-170 degrees Celsius)
por: Marc Favre, CERN
Publicado: (2006)

Coupling of CB-2 and CB-1
por: Ansaldo
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Situation of CB+1/CB+2 mid January 2004
por: Ansaldo
Publicado: (2004)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

CB0 wound
por: Ansaldo
Publicado: (2004)

Mounting of Blocks at DWE
por: Franck Stach, ST Division
Publicado: (2000)

Mounting od HE-1 support tube
por: Lucien Veillet
Publicado: (2002)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Construction of mandrel CB-2
por: Ansaldo
Publicado: (2002)

Last layer of CB-2
por: Ansaldo
Publicado: (2003)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

Loading CB-2 on board
por: Ansaldo
Publicado: (2004)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Mounting the first Barrel Wheel of the Magnet Yoke
Publicado: (2000)

Typical surface finish of the CMS magnet conductor pieces, before and after machining on the electron Beam Welding line at Techmeta
por: Benoit CURE
Publicado: (2002)

Images of CMS Superconducting Solonoid - Ancillaries
por: Perinic, G, et al.
Publicado: (2008)

Manufacture of Outer Vactank Shell for CMS.
por: Franz Leher, DWE, et al.
Publicado: (2000)

Cannot write session to /tmp/vufind_sessions/sess_e84bskt0bevc9v5plrnrt564bn