Cargando…

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly

CMS Solenoid module CB+1. Pictures taken before thermal shield assembly

Detalles Bibliográficos
Autor principal:	LEVESY
Publicado:	2005
Materias:	Magnet
Acceso en línea:	http://cds.cern.ch/record/837406

Ejemplares similares

CMS Solenoid module CB+2. Pictures taken before thermal shield assembly
por: LEVESY
Publicado: (2005)

CMS solenoid Pictures of the modules CB-2 before installation of the thermal shields.
por: LEVESY
Publicado: (2005)

CMS solenoid module CB0 pictures before shield mounting
por: LEVESY
Publicado: (2005)

CMS Solenoid module CB-1 before mounting of shield.
por: LEVESY
Publicado: (2005)

Assembly of the CMS Solenoid Inner Thermal Shield
por: Bruno LEVESY
Publicado: (2004)

Delivery of the 5 modules of the CMS Solenoid
por: Bruno LEVESY
Publicado: (2004)

CMS solenoid swivelling
por: Bruno LEVESY
Publicado: (2005)

CMS superconducting solenoid yoke
por: Brice, M, et al.
Publicado: (2008)

Magnet Outside scan before thermal shield installation
por: Hoch, Michael
Publicado: (2008)

CMS superconducting solenoid model coil
por: Perrella, M
Publicado: (2000)

CMS Solenoid Magnet during Long Shutdown 1 (LS1)
por: Hoch, Micheal
Publicado: (2013)

Picture of cabling operation, taken at Brugg Kabelwerk during the last campaign in November 2002
por: B. Blau
Publicado: (2002)

The CMS solenoid goes down to 100 Kelvin (-170 degrees Celsius)
por: Marc Favre, CERN
Publicado: (2006)

Coupling of CB-2 and CB-1
por: Ansaldo
Publicado: (2003)

CB0 is finished machining, and for CB+1 the shell is finished.
por: P. Fabbricatore
Publicado: (2003)

CB-1 after impregnation ready for coupling with CB-2.
por: Ansaldo
Publicado: (2003)

Situation of CB+1/CB+2 mid January 2004
por: Ansaldo
Publicado: (2004)

Winding of CB-1
por: P. Fabbricatore
Publicado: (2003)

Situation of mandrel manufacture (CB-1 & CB0) end of November 2002
por: Ansaldo
Publicado: (2002)

Situation on 15 May 2002, mandrel CB-2 et CB-1, prototype & impregnation chamber
por: Ansaldo
Publicado: (2002)

CB0 wound
por: Ansaldo
Publicado: (2004)

Assembly of the first Magnet Barrel Yoke Wheel in DWE factory (Deggendorf, Germany) September 1999. On the picture people from the CMS delegation are visible and give the scale.
Publicado: (1999)

CB-2 ready for impregnation
por: P. Fabbricatore
Publicado: (2003)

Construction of mandrel CB-2
por: Ansaldo
Publicado: (2002)

Last layer of CB-2
por: Ansaldo
Publicado: (2003)

External layer of CB-2
por: Ansaldo
Publicado: (2002)

Loading CB-2 on board
por: Ansaldo
Publicado: (2004)

Assembly of platform for thermal load
por: L. Veillet
Publicado: (2002)

Loading of CB-2 in Genova harbour
por: Ansaldo
Publicado: (2004)

Unloading of CB-2 at Point 5
por: L. Veillet
Publicado: (2004)

Fixation of neutron shielding on YN-1
por: Lucien Veillet
Publicado: (2002)

EBW line assembly status for CMS conductor
por: Techmeta
Publicado: (2000)

Travel of CB-2 towards Point 5
por: L. Veillet
Publicado: (2004)

Mandrel CB-2 ready for flange welding
por: Ansaldo
Publicado: (2002)

Insertion Test of the Inner Vacuum Tank inside the Outer Vacuum Tank
por: B. LEVESY
Publicado: (2002)

Test of the coil bus-bar way-out
por: B. LEVESY
Publicado: (2002)

Tie rod insertion test
por: B. LEVESY
Publicado: (2002)

Multi Layer Insulation installation around the Inner Vaccum Tank by Jéhier.
por: Bruno LEVESY
Publicado: (2003)

Pictures of YB0 and nose.
Publicado: (2002)

Actual status of the CMS barrel assembly in SX5 hall
por: Petiot Pascal
Publicado: (2001)

Cannot write session to /tmp/vufind_sessions/sess_ml2ge21ua6bkjbbe9pj0up38kn