Cargando…

A Cathode Strip Chamber with signatures from the people who helped in its construction.

Detalles Bibliográficos
Autor principal:	David Barney
Publicado:	2006
Materias:	OUTREACH Muon Detector
Acceso en línea:	http://cds.cern.ch/record/935138

Ejemplares similares

Completion of cathode strip chamber (CSC) installation on the "plus" endcap of CMS
por: Richard Breedon, UC Davis
Publicado: (2006)

Installation of the first Cathode Strip Chambers (CSC) of CMS at P5 (Cessy, France) on June 2003
Publicado: (2003)

Completion of cathode strip chamber (CSC) installation on the so-called YE+2 wheel of CMS on March 2005.
por: Tejinder S. Virdee
Publicado: (2005)

CMS Cathode Strip Chambers (CSC) extraction
por: Lapka, Marzena
Publicado: (2019)

Images of the CMS Muons - Cathode Strip Chambers (CSC)
por: Breedon, R, et al.
Publicado: (2008)

Installation of some Cathode Strip Chambers on March 2004
por: Richard Breedon
Publicado: (2004)

Early Construction: Muon Chambers
por: Hoch, Michael
Publicado: (2007)

Arrival at CERN of the first MB4 DT chambers from Turin
por: Marcos Fernandez Garcia
Publicado: (2005)

Assembly of Drift Tubes (DT) Chambers at CIEMAT (Madrid)
por: Jesus Puerta-Pelayo
Publicado: (2003)

RPC chamber with a real pannel of readout strips
por: Hoch, M
Publicado: (2011)

Completion of installation of DT and RPC chambers before Cosmic Challenge
por: Mimmo Dattola
Publicado: (2006)

Assembly and tests of Resistive Plate Chambers (RPC) for the CMS barrel detector
por: Gabriella Pugliese, Bari, et al.
Publicado: (2006)

Commissioning activities of CMS Drift Tubes (DT) chambers at SX5
por: Domenico Dattola
Publicado: (2005)

First DT+RPC chambers installation round in the UX5 cavern
por: Jesus Puerta-Pelayo
Publicado: (2007)

First test in a muon beam with two muon DT chambers of CMS
por: Michael Bontenackels
Publicado: (2004)

First joint test beam of CMS Drift Tubes (DT) and Resistive Plate Chambers (RPC)
por: Paolo Giacomelli
Publicado: (2001)

An ME234/2 EMU chamber with a laminated prototype cooling plate mounted. Dummy cathode boards and cathode board covers are installed.
por: Sergei Lusin
Publicado: (2000)

Slat chamber assembly: closing the two cathode planes
por: Cicalo, C.
Publicado: (2004)

ALICE Muon Arm, cathode pad readout chamber.
Publicado: (2003)

An Endcap Muon CSC with a prototype cooling plate mounted on the chamber frame. Visible are the aluminum cover supports that mount between the cathode front-end boards.
por: Sergei Lusin
Publicado: (2000)

MWPC cathode plane. Prototype built in Oct 2000
por: Schneider, T
Publicado: (2000)

Installation of Endcap Muon Chambers
por: Dan Wenman
Publicado: (2003)

Installation of muon chambers on endcap
por: Farshid Feyzi
Publicado: (2004)

CMS detects the first muons crossing two barrel sectors
por: Franco Gonella, et al.
Publicado: (2006)

View through the CMS detector during the cooldown of the solenoid on February 2006
por: Richard Breedon, UC Davis
Publicado: (2006)

First installation of DT and RPC packages into the CMS iron yoke
por: Jesus Puerta-Pelayo
Publicado: (2004)

Installation of ME1/1 Dubna chambers on the endcap disk YE-1
Publicado: (2005)

An ME234/2 EMU chamber with a prototype copper cooling plate mounted on frame. Cooling plate is fully instrumented with cathode front-end boards, ALCT and low-voltage distribution board. All cable harnesses and strain reliefs are in place.
por: Sergei Lusin
Publicado: (2000)

Photogrammetry of the new CSC chambers at the CMS Experiment
por: Behrens, Antje, et al.
Publicado: (2013)

CMS GE1/1 chambers at Prevessin lab
por: Starling, Elizabeth Rose
Publicado: (2019)

Images of CMS MUONs - Resistive Plate Chambers (RPC)
por: Puerta-Pelayo, J
Publicado: (2008)

Early Construction: Muon Chambers
por: Hoch, Michael
Publicado: (2007)

First test of a CMS DT chamber equipped with full electronics in a muon beam
por: Jesus Puerta-Pelayo
Publicado: (2003)

A view of YE+1 after the installation of the first layer of RE1/3 RPC chambers.
Publicado: (2006)

Tests of Cathode Strip Chamber Prototypes
por: Bonushkin, Yuri, et al.
Publicado: (1997)

Pictures showing the test of CSC installation fixture. The CSC is fully balanced and free to rotate to any angle. After CSC is attached to mounts, fixture is rebalanced and removed. Electrical limits stops are set at with or without chamber balance points.
por: Farshid Feyzi, et al.
Publicado: (2001)

Tests of cathode strip chamber prototypes
por: Baarmand, M M, et al.
Publicado: (1998)

Data analysis for cathode strip chamber
por: Zubov, K A, et al.
Publicado: (1999)

Spatial Resolution Studies in Cathode Pad and in Cathode Strip Chambers
por: Bimbot, L, et al.
Publicado: (1997)

Performance Testing of the CMS Cathode Strip Chambers
por: Breedon, Richard, et al.
Publicado: (2009)

Cannot write session to /tmp/vufind_sessions/sess_m3ivb6rt7ifsklkculvpkqidfc