Cargando…

Electrical insulation testing for ITER fusion tokamak

The uniqueness of the ITER fusion project drives purpose and scope here to fulfil (functional) Procurement Arrangement (PA) requirements for the Central Solenoid (CS) and Correction Coil (CC) magnets' electrical insulation [1-3]; as used and undertaken for covering high voltage testing operatio...

Descripción completa

Detalles Bibliográficos
Autores principales:	Gaxiola, E, Evans, D, Laquiere, J, Laurenti, A, Libeyre, P, Lyraud, C, Piccin, R, Rinaudo, G, Simon, F, Vollmann, T, Martovetsky, N, Niu, E, Langeslag, S, Sgobba, S, Khumthong, K, Norausky, N, Smith, J, Wei, J, Wu, H, Yu, X
Lenguaje:	eng
Publicado:	2017
Materias:	Engineering
Acceso en línea:	https://dx.doi.org/10.1109/EIC.2017.8004670 http://cds.cern.ch/record/2303655

Ejemplares similares

Starting Manufacture of the ITER Central Solenoid
por: Libeyre, P, et al.
Publicado: (2016)

Extensive Characterisation of Copper-clad Plates, Bonded by the Explosive Technique, for ITER Electrical Joints
por: Langeslag, S A E, et al.
Publicado: (2015)

Characterization of low temperature high voltage axial insulator breaks for the ITER cryogenic supply line
por: Fernandez Pison, P, et al.
Publicado: (2017)

Examination of ITER Central Solenoid prototype joints
por: Aviles Santillana, I, et al.
Publicado: (2019)

Manufacture of the ITER Central Solenoid Components
por: Libeyre, Paul, et al.
Publicado: (2018)

Extensive characterisation of advanced manufacturing solutions for the ITER Central Solenoid pre-compression system
por: Langeslag, S.A.E., et al.
Publicado: (2015)

Qualification of the Manufacturing Procedures of the ITER Correction Coils
por: Libeyre, P, et al.
Publicado: (2017)

Design of load-to-failure tests of high-voltage insulation breaks for ITER's cryogenic network
por: Langeslag, S A E, et al.
Publicado: (2015)

Physical Properties of a High-Strength Austenitic Stainless Steel for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2016)

Requirements for qualification of manufacture of the ITER Central Solenoid and Correction Coils
por: Libeyre, Paul, et al.
Publicado: (2015)

Advanced examination techniques applied to the qualification of critical welds for the ITER correction coils
por: Sgobba, Stefano, et al.
Publicado: (2015)

Final Design of ITER In-Vessel Coils and Manufacturing of In-Vessel Coil Conductor
por: Encheva, Anna, et al.
Publicado: (2022)

Qualification of ITER Correction Coil Superconducting Joint
por: Wang, Lin, et al.
Publicado: (2018)

Assessment of Residual Stresses in ITER CS Helium Inlet Welds Fatigue Tested at Cryogenic Temperature
por: Sgobba, S, et al.
Publicado: (2019)

From manufacture to assembly of the ITER central solenoid
por: Libeyre, P, et al.
Publicado: (2019)

Investigation of Materials and Welds for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2018)

Qualification of structural stainless steel products for the ITER correction coil cases
por: Sgobba, Stefano, et al.
Publicado: (2017)

Design, construction, and testing of no-insulation small subscale solenoids for compact tokamaks
por: Zhai, Yuhu, et al.
Publicado: (2021)

Tokamaks
por: Wesson, John
Publicado: (2011)

Tokamaks
por: Wesson, John
Publicado: (2004)

Advanced Examination Techniques Applied to the Assessment of Vacuum Pressure Impregnation (VPI) of ITER Correction Coils
por: Sgobba, Stefano, et al.
Publicado: (2014)

Design Optimization and Assessment of Fabrication of ITER Central Solenoid Twin Box Joints
por: Santillana, Ignacio Aviles, et al.
Publicado: (2020)

Post-mortem analysis of ITER CS helium inlets fatigue tested at cryogenic temperature
por: Aviles Santillana, I, et al.
Publicado: (2019)

Control of the TCV Tokamak
por: Lister, J B, et al.
Publicado: (1990)

The Control of Modern Tokamaks
por: Lister, J B, et al.
Publicado: (1999)

Progress of the ITER Correction Coils in China
por: Wei, J, et al.
Publicado: (2014)

Microstructure and Mechanical Properties of ITER Correction Coil Case Material
por: Xin, Jijun, et al.
Publicado: (2017)

Examination and Assessment of Large Forged Structural Components for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2020)

Metallurgical assessment of large size tensioning components for the precompression structure of the ITER central solenoid
por: Sgobba, Stefano, et al.
Publicado: (2021)

Examination and Characterization of Physical and Mechanical Properties of the ITER Central Solenoid Module Coils
por: Sgobba, Stefano, et al.
Publicado: (2022)

Tokamak confinement scaling laws
por: Connor, J W
Publicado: (1998)

Magnetohydrodynamic stability of tokamaks
por: Zohm, Hartmut
Publicado: (2014)

Theory of tokamak plasmas
por: White, RB
Publicado: (1989)

Tokamak engineering mechanics
por: Song, Yuntao, et al.
Publicado: (2013)

The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case
por: Fang, Chao, et al.
Publicado: (2014)

Control and protection system for the Varennes Tokamak
por: Iliev, Bozhidar Z, et al.
Publicado: (1990)

The role of limiter in Egyptor Tokamak
por: Ei-Sisi, A B, et al.
Publicado: (2002)

The role of limiter in Egyptor Tokamak
por: El-Sisi, A B, et al.
Publicado: (2002)

The frontier and perspective for tokamak development
por: Li, Jiangang, et al.
Publicado: (2019)

The Effect of Specific Manufacturing Characteristics on PF ITER Full-Size Joint Performance
por: Pison, Pilar Fernandez, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_tfjt1fjtole4sbdfa67u1tu6rd