Cargando…

Microstructure and Mechanical Properties of the Enclosure Welding Joint for ITER Correction Coils Cases

To resist the alternating electromagnetic loads, the International Thermonuclear Experimental Reactor (ITER) correction coils are protected by a 20-mm-thick 316LN austenitic stainless steel case. According to the strict tolerance requirement of the case manufacture, laser welding was applied to encl...

Descripción completa

Detalles Bibliográficos
Autores principales:	Xin, Jijun, Fang, Chao, Yang, Wuxiong, Huang, Chuanjun, Dai, Wenhua, Wei, Jing, Song, Yuntao, Li, Laifeng, Fabrice, Simon, Paul, Libeyre, Sgobba, Stefano
Lenguaje:	eng
Publicado:	2020
Acceso en línea:	https://dx.doi.org/10.1109/TASC.2020.2976588 http://cds.cern.ch/record/2717123

Ejemplares similares

Microstructure and Mechanical Properties of ITER Correction Coil Case Material
por: Xin, Jijun, et al.
Publicado: (2017)

Advanced examination techniques applied to the qualification of critical welds for the ITER correction coils
por: Sgobba, Stefano, et al.
Publicado: (2015)

The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case
por: Fang, Chao, et al.
Publicado: (2014)

Qualification of ITER Correction Coil Superconducting Joint
por: Wang, Lin, et al.
Publicado: (2018)

Qualification of structural stainless steel products for the ITER correction coil cases
por: Sgobba, Stefano, et al.
Publicado: (2017)

Advanced Examination Techniques Applied to the Assessment of Vacuum Pressure Impregnation (VPI) of ITER Correction Coils
por: Sgobba, Stefano, et al.
Publicado: (2014)

Progress of the ITER Correction Coils in China
por: Wei, J, et al.
Publicado: (2014)

Investigation of Materials and Welds for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2018)

Qualification of the Manufacturing Procedures of the ITER Correction Coils
por: Libeyre, P, et al.
Publicado: (2017)

Examination of ITER Central Solenoid prototype joints
por: Aviles Santillana, I, et al.
Publicado: (2019)

Requirements for qualification of manufacture of the ITER Central Solenoid and Correction Coils
por: Libeyre, Paul, et al.
Publicado: (2015)

Assessment of Residual Stresses in ITER CS Helium Inlet Welds Fatigue Tested at Cryogenic Temperature
por: Sgobba, S, et al.
Publicado: (2019)

Extensive Characterisation of Copper-clad Plates, Bonded by the Explosive Technique, for ITER Electrical Joints
por: Langeslag, S A E, et al.
Publicado: (2015)

Examination and Characterization of Physical and Mechanical Properties of the ITER Central Solenoid Module Coils
por: Sgobba, Stefano, et al.
Publicado: (2022)

Final Design of ITER In-Vessel Coils and Manufacturing of In-Vessel Coil Conductor
por: Encheva, Anna, et al.
Publicado: (2022)

Design Optimization and Assessment of Fabrication of ITER Central Solenoid Twin Box Joints
por: Santillana, Ignacio Aviles, et al.
Publicado: (2020)

EBSD Characterization of the Microstructure of 7A52 Aluminum Alloy Joints Welded by Friction Stir Welding
por: Liu, Xu, et al.
Publicado: (2021)

Physical Properties of a High-Strength Austenitic Stainless Steel for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2016)

Examination and Assessment of Large Forged Structural Components for the Precompression Structure of the ITER Central Solenoid
por: Sgobba, Stefano, et al.
Publicado: (2020)

Metallurgical assessment of large size tensioning components for the precompression structure of the ITER central solenoid
por: Sgobba, Stefano, et al.
Publicado: (2021)

Possible fabrication techniques and welding specifications for the external cylinder of the CMS coil
por: Castoldi, M, et al.
Publicado: (2000)

Post-mortem analysis of ITER CS helium inlets fatigue tested at cryogenic temperature
por: Aviles Santillana, I, et al.
Publicado: (2019)

Extensive characterisation of advanced manufacturing solutions for the ITER Central Solenoid pre-compression system
por: Langeslag, S.A.E., et al.
Publicado: (2015)

The Effect of Welding Energy on the Microstructural and Mechanical Properties of Ultrasonic-Welded Copper Joints
por: Yang, Jingwei, et al.
Publicado: (2017)

Validation of Helium Inlet Design for ITER Toroidal Field Coil
por: Boyer, C, et al.
Publicado: (2014)

Microstructure and Properties of Surface-Modified Plates and Their Welded Joints
por: Wang, Tai, et al.
Publicado: (2019)

Influence of Welding Speeds on the Morphology, Mechanical Properties, and Microstructure of 2205 DSS Welded Joint by K-TIG Welding
por: Cui, Shuwan, et al.
Publicado: (2021)

Effect of Post-Weld Heat Treatment on Microstructure and Fracture Toughness of X80 Pipeline Steel Welded Joint
por: Wang, Xueli, et al.
Publicado: (2022)

The Effect of Specific Manufacturing Characteristics on PF ITER Full-Size Joint Performance
por: Pison, Pilar Fernandez, et al.
Publicado: (2019)

Effect of Post-Weld Annealing on Microstructure and Growth Behavior of Copper/Aluminum Friction Stir Welded Joint
por: Jin, Yuhua, et al.
Publicado: (2020)

Microstructure Evolution and Mechanical Properties of Thick 2219 Aluminum Alloy Welded Joints by Electron-Beam Welding
por: Chang, Zhilong, et al.
Publicado: (2023)

Microstructure Control of Welded Joints of Dissimilar Titanium Alloys by Isothermal Forging
por: Zhang, Yongqiang, et al.
Publicado: (2020)

Effect of Welding Speed and Post Quenching on the Microstructure and Mechanical Properties of Laser-Welded B1500HS Joints
por: Li, Muyu, et al.
Publicado: (2020)

Reliability of the longitudinal welds of LHC main dipoles
por: Fessia, P, et al.
Publicado: (2004)

The Microstructure and Mechanical Properties of Multi-Strand, Composite Welding-Wire Welded Joints of High Nitrogen Austenitic Stainless Steel
por: Li, Jianguo, et al.
Publicado: (2019)

Microstructure, Fractography, and Mechanical Properties of Hardox 500 Steel TIG-Welded Joints by Using Different Filler Weld Wires
por: Zuo, Zhaoyang, et al.
Publicado: (2022)

Influence of Shielding Gas on Microstructure and Properties of GMAW DSS2205 Welded Joints
por: Zhang, Xin-Yu, et al.
Publicado: (2021)

Influence of Long-Term Subcritical Annealing on the Unalloyed Steel Welded Joint Microstructure
por: Fajt, Dominika, et al.
Publicado: (2022)

Evaluation of the Properties and Microstructure of Thick-Walled Welded Joint of Wear Resistant Materials
por: Krawczyk, Ryszard, et al.
Publicado: (2022)

The Influence of Post-Weld Heat Treatment on the Microstructure and Fatigue Properties of Sc-Modified AA2519 Friction Stir-Welded Joint
por: Kosturek, Robert, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_oirv3u16g0am8ljgus59vf39pe