Cargando…

Assembly and Test of the HL-LHC Twin Aperture Orbit Corrector Based on Canted Cos-Theta Design

In the frame of the high-luminosity upgrade project (HL-LHC) at CERN, a double aperture, independently powered, family of beam orbit corrector magnets will be installed close to the two main LHC experiments Atlas and CMS. These 2.6 T magnets, built using a canted cos-theta design. This paper describ...

Descripción completa

Detalles Bibliográficos
Autores principales:	Kirby, G, Van Nugteren, J, Mentink, M, Canale, M, Gentini, L, Mazet, J, Pincot, F O, Mangiarotti, F J, Fiscarelli, L, Steckert, J, Coelingh, G J, de Rijk, G, Perez, J C, Verweij, A, Todesco, E, Rossi, L
Lenguaje:	eng
Publicado:	IOP 2020
Materias:	Accelerators and Storage Rings
Acceso en línea:	https://dx.doi.org/10.1088/1742-6596/1559/1/012070 http://cds.cern.ch/record/2725897

Ejemplares similares

Test of the First Full-Length Prototype of the HL-LHC D2 Orbit Corrector Based on Canted Cosine Theta Technology
por: Mangiarotti, Franco J, et al.
Publicado: (2020)

Quench Behavior of Prototype Nb-Ti HL-LHC Dipole Canted Cos-Theta Orbit Corrector Magnets
por: Wozniak, Mariusz, et al.
Publicado: (2022)

Hi-Lumi LHC Twin Aperture Orbit Correctors 0.5-m Model Magnet Development and Cold Test
por: Kirby, Glyn A, et al.
Publicado: (2018)

Hi-Lumi LHC Twin-Aperture Orbit Correctors Magnet System Optimisation
por: Kirby, Glyn A, et al.
Publicado: (2017)

Test of short model and prototype of the HL-LHC D2 orbit corrector based on CCT technology
por: Mangiarotti, Franco, et al.
Publicado: (2019)

Quench Behavior of the HL-LHC Twin Aperture Orbit Correctors
por: Mentink, Matthias, et al.
Publicado: (2018)

Design of a Canted-cosine-theta orbit corrector for the High Luminosity LHC
por: Pepitone, K., et al.
Publicado: (2022)

Design and Fabrication of a Canted-Cosine-Theta Double Aperture Orbit Corrector Dipole for the LHC
por: Pepitone, K, et al.
Publicado: (2023)

Simulated Versus Experimentally Observed Quench Behavior of the HL-LHC Twin Aperture Orbit Corrector Prototype
por: Mentink, Matthias, et al.
Publicado: (2020)

Fast Quench Propagation Conductor for Protecting Canted Cos-Theta Magnets
por: Wozniak, Mariusz, et al.
Publicado: (2023)

FEM modeling of multilayer Canted Cosine Theta (CCT) magnets with orthotropic material properties
por: Ortwein, R, et al.
Publicado: (2020)

Cos-$\theta$ design of dipole inserts made of ReBCO-Roebel or BSCCO-Rutherford cables
por: Lorin, C, et al.
Publicado: (2015)

Manufacturing of the EuCARD2 Roebel-Based Cos-Theta Coils at CEA Saclay
por: Durante, Maria, et al.
Publicado: (2020)

Mechanical design of a nested 4-layer Canted Cosine Theta (CCT) dipole
por: Ortwein, Rafal, et al.
Publicado: (2020)

Magnetic measurements of MCBC and MCBY orbit correctors under special cycling conditions
por: Chmielinska, Agnieszka, et al.
Publicado: (2022)

High-temperature superconducting screens for magnetic field-error cancellation in accelerator magnets
por: Bortot, L., et al.
Publicado: (2021)

Magnetic measurements on the prototype magnets of the high-order correctors for HL-LHC
por: Fiscarelli, Lucio, et al.
Publicado: (2019)

Magneto-Mechanical Optimization of Cross-Sections for $\textrm{cos}(\theta)$ Accelerator Magnets
por: Vallone, G, et al.
Publicado: (2022)

Quench propagation in Nb$_{3}$Sn cos-theta 11 T dipole model magnets in high stress areas
por: Mangiarotti, Franco J, et al.
Publicado: (2018)

Status of the Production of the LHC Superconducting Corrector Magnets
por: Allitt, M, et al.
Publicado: (2004)

Magnetization in superconducting corrector magnets and impact on luminosity-calibration scans in the Large Hadron Collider
por: Chmielinska, Agnieszka, et al.
Publicado: (2023)

Proposal to Increase the LEP Energy with Horizontal Orbit Correctors
por: Beuret, A, et al.
Publicado: (2000)

First Short Orbit Nested Corrector Magnet for HL-LHC Produced in the Industry
por: Jardim, C Martins, et al.
Publicado: (2023)

Development and test of Nb$_3$Sn cos-theta dipoles based on PIT strands
por: Zlobin, A V, et al.
Publicado: (2005)

Conceptual design of the orbit correctors for D2 and Q4
por: Rysti, J, et al.
Publicado: (2015)

Power Tests of the First Nested Orbit Corrector Prototype for HL-LHC
por: García-Matos, Jesús A, et al.
Publicado: (2020)

Study of the Quench Propagation and of the Protection System of the COS-theta NED Dipole Prototype
por: Granata, V, et al.
Publicado: (2006)

Recent Test Results of the Fast-Pulsed 4 T COS$\Theta$ Dipole GSI 001
por: Moritz, G, et al.
Publicado: (2005)

Development of Superconducting Tuning Quadrupole Corrector (MQT) Prototypes for the LHC
por: Allitt, M, et al.
Publicado: (2002)

The UT-CERN Cos-theta LHC-Type Nb$_{3}$Sn Dipole Magnet
por: ten Kate, Herman H J, et al.
Publicado: (2019)

Superconducting Curved Canted–Cosine–Theta (CCT) for the HIE-ISOLDE Recoil Separator Ring at CERN
por: Kirby, G, et al.
Publicado: (2022)

Further Development of the Sextupole and Decapole Spool Corrector Magnets for the LHC
por: Allitt, M, et al.
Publicado: (1999)

Accelerator Quality HTS Dipole Magnet Demonstrator Designs for the EuCARD-2, 5 Tesla 40 mm Clear Aperture Magnet
por: Kirby, G A, et al.
Publicado: (2015)

FRITIOF6: test of Q- and cos(Theta) distributions for pipi-pairs
por: Gortchakov, O
Publicado: (2005)

Development of Cos-Theta $\Nb_{3}Sn$ Dipole Magnets for VLHC
por: Zlobin, A
Publicado: (2001)

Cable Desigh for Fast Ramped Superconducting Magnets ($Cos-\theta$ Design)
por: Ghosh, A K
Publicado: (2005)

Design of a Cloverleaf-Racetrack Dipole Demonstrator Magnet With Dual $Re$BCO Conductor
por: Nes, T.H., et al.
Publicado: (2022)

Design and operational aspects of a bi-polar semi-conductor switch as possible candidate for replacement of electro-mechanical switchgear in energy extraction systems for the LHC corrector magnet circuits
por: Coelingh, G J, et al.
Publicado: (2014)

First Prototype of the Long Orbit Nested Corrector for HL-LHC
por: Toral, F, et al.
Publicado: (2023)

Design Study of the Nb₃Sn Cos-Theta Dipole Model for FCC-hh
por: Valente, Riccardo U, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_plu2onkt78iot3l5t9upicnl4o