Cargando…

The Effect of Cooling Rates on Thermal, Crystallization, Mechanical and Barrier Properties of Rotational Molding Polyamide 11 as the Liner Material for High-Capacity High-Pressure Vessels

The rapid development of hydrogen fuel cells has been paralleled by increased demand for lightweight type IV hydrogen storage vessels with high hydrogen storage density, which raises the performance requirements of internal plastic liners. An appropriate manufacturing process is important to improve...

Descripción completa

Detalles Bibliográficos
Autores principales:	Yu, Muhuo, Qi, Liangliang, Cheng, Lele, Min, Wei, Mei, Zhonghao, Gao, Ruize, Sun, Zeyu
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10053686/ https://www.ncbi.nlm.nih.gov/pubmed/36985398 http://dx.doi.org/10.3390/molecules28062425

Ejemplares similares

Optimization of the Laminate Structure of a Composite Cylinder Based on the Combination of Response Surface Methodology (RSM) and Finite Element Analysis (FEA)
por: Li, Zhiqi, et al.
Publicado: (2022)

Novel Use of the GuideLiner Catheter to Deliver Rotational Atherectomy Burrs in Tortuous Vessels
por: Vo, Minh, et al.
Publicado: (2014)

Effects of Heating and Cooling of Injection Mold Cavity Surface and Melt Flow Control on Properties of Carbon Fiber Reinforced Semi-Aromatic Polyamide Molded Products
por: Murata, Yasuhiko, et al.
Publicado: (2021)

Preparation of High-Performance Carbon Fiber-Reinforced Epoxy Composites by Compression Resin Transfer Molding
por: Sun, Zeyu, et al.
Publicado: (2018)

Peel strength of denture liner to PMMA and polyamide: laser versus air-abrasion
por: Korkmaz, Fatih Mehmet, et al.
Publicado: (2013)

High-Performance of a Thick-Walled Polyamide Composite Produced by Microcellular Injection Molding
por: Sykutera, Dariusz, et al.
Publicado: (2021)

Rapid Development of an Injection Mold with High Cooling Performance Using Molding Simulation and Rapid Tooling Technology
por: Kuo, Chil-Chyuan, et al.
Publicado: (2021)

Mechanical Behavior—Microstructure Relationships in Injection-Molded Polyamide 66
por: Billon, Noëlle, et al.
Publicado: (2018)

Hydrogen Permeability of Polyamide 6 Used as Liner Material for Type IV On-Board Hydrogen Storage Cylinders
por: Dong, Chufeng, et al.
Publicado: (2023)

Thermal and Mechanical Analysis of Polyethylene Homo-Composites Processed by Rotational Molding
por: Greco, Antonio, et al.
Publicado: (2019)

Thermoplastic Overmolding onto Injection-Molded and In Situ Polymerization-Based Polyamides
por: Boros, Róbert, et al.
Publicado: (2018)

Process Induced Skin-Core Morphology in Injection Molded Polyamide 66
por: Spoerer, Yvonne, et al.
Publicado: (2020)

Morphological, thermal and mechanical properties of recycled HDPE foams via rotational molding
por: Dou, Yao, et al.
Publicado: (2021)

Injection-Molded Parts of Partially Biobased Polyamide 610 and Biobased Halloysite Nanotubes
por: Marset, David, et al.
Publicado: (2020)

Effect of cylinder-liner rotation on wear rate: An experimental study
por: Musmar, Sa'ed A., et al.
Publicado: (2019)

Crystallization and Performance of Polyamide Blends Comprising Polyamide 4, Polyamide 6, and Their Copolymers
por: Zhang, Yajing, et al.
Publicado: (2023)

Highly effective photon-to-cooling thermal device
por: Tian, Yanpei, et al.
Publicado: (2019)

Perfluoropolyether (PFPE) Intermediate Molds for High-Resolution Thermal Nanoimprint Lithography
por: Masciullo, Cecilia, et al.
Publicado: (2018)

Heteroaromatic Polyamides with Improved Thermal and Mechanical Properties
por: Trigo-López, Miriam, et al.
Publicado: (2020)

Thermal, Mechanical, Morphological and Aesthetical Properties of Rotational Molding PE/Pine Wood Sawdust Composites
por: Martins, Carla I., et al.
Publicado: (2022)

Weld Line Strength of Polyamide Fiberglass Composite at Different Processing Parameters in Injection Molding Technique
por: Nguyen, Van-Thuc, et al.
Publicado: (2023)

Internal Gas-Assisted Mold Temperature Control for Improving the Filling Ability of Polyamide 6 + 30% Glass Fiber in the Micro-Injection Molding Process
por: Uyen, Tran Minh The, et al.
Publicado: (2022)

Control of Gray Mold on Clamshell-Packaged ‘Benitaka’ Table Grapes Using Sulphur Dioxide Pads and Perforated Liners
por: Junior, Osmar Jose Chaves, et al.
Publicado: (2019)

Effects of Different Mold Materials and Coolant Media on the Cooling Performance of Epoxy-Based Injection Molds
por: Kuo, Chil-Chyuan, et al.
Publicado: (2022)

The Effect of Mold Structure and Cooling Parameters on Heat Transfer during Billet High-Speed Continuous Casting
por: Wang, Sijie, et al.
Publicado: (2023)

Shrinkage and Warpage Minimization of Glass-Fiber-Reinforced Polyamide 6 Parts by Microcellular Foam Injection Molding
por: Ryu, Youngjae, et al.
Publicado: (2020)

Reproducibility Study of the Thermoplastic Resin Transfer Molding Process for Glass Fiber Reinforced Polyamide 6 Composites †
por: Martins, Filipe P., et al.
Publicado: (2023)

Improving Cooling Performance of Injection Molding Tool with Conformal Cooling Channel by Adding Hybrid Fillers
por: Kuo, Chil-Chyuan, et al.
Publicado: (2021)

Recent Developments in Inorganic Composites in Rotational Molding
por: Ortega, Zaida, et al.
Publicado: (2022)

The Ringloc liner compared with the Hexloc liner in total hip arthroplasty
por: Olof, Sköldenberg, et al.
Publicado: (2009)

Targetry, bunch rotation, cooling
por: Bisoffi, G, et al.
Publicado: (1989)

Rotational Doppler cooling and heating
por: Pan, Deng, et al.
Publicado: (2021)

Kinetics of the Thermal Degradation of Poly(lactic acid) and Polyamide Bioblends
por: Carrasco, Félix, et al.
Publicado: (2021)

Spin-Trapping Analysis of the Thermal Degradation Reaction of Polyamide 66
por: Kurima, Akihiro, et al.
Publicado: (2022)

Application of New Conformal Cooling Layouts to the Green Injection Molding of Complex Slender Polymeric Parts with High Dimensional Specifications
por: Torres-Alba, Abelardo, et al.
Publicado: (2023)

Penetration Behavior of High-Density Reactive Material Liner Shaped Charge
por: Guo, Huanguo, et al.
Publicado: (2019)

Metal Additive Manufacturing of Plastic Injection Molds with Conformal Cooling Channels
por: Kanbur, Baris Burak, et al.
Publicado: (2022)

Characterization of Epoxy-Based Rapid Mold with Profiled Conformal Cooling Channel
por: Kuo, Chil-Chyuan, et al.
Publicado: (2022)

Simple Synthesis of Hydroxyl and Ethylene Functionalized Aromatic Polyamides as Sizing Agents to Improve Adhesion Properties of Aramid Fiber/Vinyl Epoxy Composites
por: Qin, Minglin, et al.
Publicado: (2017)

Effect of light-delignification on mechanical, hydrophobic, and thermal properties of high-strength molded fiber materials
por: Wang, Quanliang, et al.
Publicado: (2018)

Cannot write session to /tmp/vufind_sessions/sess_s28f1d2tdfv5h9rl67b9cv0nm2