Cargando…

Quenching and Tempering-Dependent Evolution on the Microstructure and Mechanical Performance Based on a Laser Additively Manufactured 12CrNi2 Alloy Steel

For exploring an effective heat treatment schedule to enhance the strength–plasticity balance of the ferrite–austenite 12CrNi2 alloy steel additively manufactured by directed energy deposition (DED), 12CrNi2 was heat-treated with deliberately designed direct quenching (DQ) and cyclic quenching (CQ),...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zhang, Wei, Shang, Xin, Chen, Xiaoxuan, Chen, Shenggui, Liu, Zhengliang, Zhang, Lijuan
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10180319/ https://www.ncbi.nlm.nih.gov/pubmed/37176325 http://dx.doi.org/10.3390/ma16093443

Ejemplares similares

Influence of heat treatment on the mechanical properties of CrNi stainless steel orthodontic wires
por: Sepúlveda, Clariana Hoehne, et al.
Publicado: (2019)

Effect of Cold-Rolling Reduction on Recrystallization Microstructure, Texture and Corrosion Properties of the X2CrNi12 Ferritic Stainless Steel
por: Li, Rui, et al.
Publicado: (2022)

Assessment of Corrosion Resistance and Hardness of Shot Peened X5CrNi18-10 Steel
por: Walczak, Mariusz, et al.
Publicado: (2022)

Numerical Simulation and Experimental Study on Residual Stress in the Curved Surface Forming of 12CrNi2 Alloy Steel by Laser Melting Deposition
por: Cui, Zhaoxing, et al.
Publicado: (2020)

Low-Cycle Fatigue Behavior of 10CrNi3MoV High Strength Steel and Its Undermatched Welds
por: Song, Wei, et al.
Publicado: (2018)

Analysis of the Possibility of Plastic Deformation Characterisation in X2CrNi18-9 Steel Using Measurements of Electromagnetic Parameters
por: Roskosz, Maciej, et al.
Publicado: (2021)

A High-Sensitivity Current Sensor Utilizing CrNi Wire and Microfiber Coils
por: Xie, Xiaodong, et al.
Publicado: (2014)

Effects of Substrate Preheating Temperatures on the Microstructure, Properties, and Residual Stress of 12CrNi2 Prepared by Laser Cladding Deposition Technique
por: Ding, Chenggang, et al.
Publicado: (2018)

Grinding Force and Surface Formation Mechanisms of 17CrNi2MoVNb Alloy When Grinding with CBN and Alumina Wheels
por: Jiang, Xiaoyang, et al.
Publicado: (2023)

Ion Irradiation-Induced Microstructural Evolution of Ni–Mo–Cr Low Alloy Steels
por: Sun, Hongying, et al.
Publicado: (2018)

Microstructure Transformation on Pre-Quenched and Ultrafast-Tempered High-Strength Multiphase Steels
por: Zhao, Yonggang, et al.
Publicado: (2019)

Deformation Behavior and Constitutive Model of 34CrNi3Mo during Thermo-Mechanical Deformation Process
por: Jia, Xiang-Dong, et al.
Publicado: (2022)

Microstructure Transformation in Laser Additive Manufactured NiTi Alloy with Quasi-In-Situ Compression
por: Yang, Xiao, et al.
Publicado: (2022)

The Characteristic Microstructures and Properties of Steel-Based Alloy via Additive Manufacturing
por: Shang, Chunlei, et al.
Publicado: (2023)

Additive Manufacturing of CrFeNiTi Multi-Principal Element Alloys
por: Reiberg, Marius, et al.
Publicado: (2022)

Effects of Cold Rolling on the Microstructure and Corrosion Resistance of the Double-Glow Plasma Ni-Cr Alloying Layer on Q235 Steel
por: Zhu, Xiaolin, et al.
Publicado: (2022)

In Situ and Ex Situ Characterization of the Microstructure Formation in Ni-Cr-Si Alloys during Rapid Solidification—Toward Alloy Design for Laser Additive Manufacturing
por: Li, Xiaoshuang, et al.
Publicado: (2020)

Microstructure and Properties of SUS304 Stainless Steel Joints Brazed with Electrodeposited Ni-Cr-P Alloy Coatings
por: Liu, Shubin, et al.
Publicado: (2021)

Hot Deformation Behavior of a Ti-40Al-10V Alloy with Quenching-Tempering Microstructure
por: Cheng, Liang, et al.
Publicado: (2018)

Additively Manufactured Commercial Co-Cr Dental Alloys: Comparison of Microstructure and Mechanical Properties
por: Viderščak, Dalibor, et al.
Publicado: (2021)

Influence of Tempering Temperature and Time on Microstructure and Mechanical Properties of Additively Manufactured H13 Tool Steel
por: Bae, Kichang, et al.
Publicado: (2022)

Effects of Cooling Rate during Quenching and Tempering Conditions on Microstructures and Mechanical Properties of Carbon Steel Flange
por: Jo, Haeju, et al.
Publicado: (2020)

Evaluation of marginal and internal gaps of Ni-Cr and Co-Cr alloy copings manufactured by microstereolithography
por: Kim, Dong-Yeon, et al.
Publicado: (2017)

Microstructure Evolution in Cu-Ni-Co-Si-Cr Alloy During Hot Compression by Ce Addition
por: Ban, Yijie, et al.
Publicado: (2020)

Microstructure Evolution and Orientation Relationship of Reverted Austenite in 13Cr Supermartensitic Stainless Steel During the Tempering Process
por: Zhang, Yiwei, et al.
Publicado: (2019)

Effect of Heat Treatment on Microstructure and Properties of 24CrNiMo Alloy Steel Formed by Selective Laser Melting (SLM)
por: Zhao, Yongsheng, et al.
Publicado: (2021)

Characterization of Carbide Precipitation during Tempering for Quenched Dievar Steel
por: Xie, Yixin, et al.
Publicado: (2022)

Effect of Si on Microstructure and Mechanical Properties of FeCrNi Medium Entropy Alloys
por: Ding, Fang, et al.
Publicado: (2023)

The Microstructure, Solidification Path, and Microhardness of As-Cast Ni-Al-Cr-Os Alloys in a Ni-Rich Region
por: Lin, Yan, et al.
Publicado: (2023)

Effect of Microstructural Evolution on the Mechanical Properties of Ni-Cr-Mo Ultra-Heavy Steel Plate
por: Guo, Kaihao, et al.
Publicado: (2023)

Stacking Fault Energy Analyses of Additively Manufactured Stainless Steel 316L and CrCoNi Medium Entropy Alloy Using In Situ Neutron Diffraction
por: Woo, W., et al.
Publicado: (2020)

The Effect of Copper on the Microstructure, Wear and Corrosion Resistance of CoCrCuFeNi High-Entropy Alloys Manufactured by Powder Metallurgy
por: Mukanov, Samat, et al.
Publicado: (2023)

Additive manufacturing of alloys with programmable microstructure and properties
por: Gao, Shubo, et al.
Publicado: (2023)

Effect of Laser Quenching-Shock Peening Strengthening on the Microstructure and Mechanical Properties of Cr12MoV Steel
por: Feng, Aixin, et al.
Publicado: (2022)

High-Resolution Microstructure Characterization of Additively Manufactured X5CrNiCuNb17-4 Maraging Steel during Ex and In Situ Thermal Treatment
por: Albu, Mihaela, et al.
Publicado: (2021)

Effect of Quenching Tempering-Post Weld Heat Treatment on the Microstructure and Mechanical Properties of Laser-Arc Hybrid-Welded Boron Steel
por: Lee, Ho Won, et al.
Publicado: (2019)

Effect of Mn Addition on the Microstructures and Mechanical Properties of CoCrFeNiPd High Entropy Alloy
por: Tan, Yiming, et al.
Publicado: (2019)

Effect of Al Addition on Microstructure and Properties of CoCrNi Medium-Entropy Alloy Prepared by Powder Metallurgy
por: Ding, Xuekun, et al.
Publicado: (2022)

Effect of Zr Addition on the Microstructure and Mechanical Properties of CoCrFeNiMn High-Entropy Alloy Synthesized by Spark Plasma Sintering
por: Zhang, Hongling, et al.
Publicado: (2018)

Microstructure Evolution and Mechanical Properties of Tempered 5140 Alloy Steel after Proton Irradiation at Different Temperatures
por: Dai, Luanyue, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_l1q8ojukr2jf4tiqbu629965af