Cargando…

Regeneration of the Damaged Parts with the Use of Metal Additive Manufacturing—Case Study

The paper shows the results related to regeneration possibilities analysis of a damaged slider removed from a hydraulic splitter that was repaired using additive manufacturing (AM), laser-based powder bed fusion of metals (PBF-LB/M) technology. The results demonstrate the high quality of the connect...

Descripción completa

Detalles Bibliográficos
Autores principales:	Sawczuk, Piotr, Kluczyński, Janusz, Sarzyński, Bartłomiej, Szachogłuchowicz, Ireneusz, Jasik, Katarzyna, Łuszczek, Jakub, Grzelak, Krzysztof, Płatek, Paweł, Torzewski, Janusz, Małek, Marcin
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10223511/ https://www.ncbi.nlm.nih.gov/pubmed/37241398 http://dx.doi.org/10.3390/ma16103772

Ejemplares similares

A Comparative Investigation of Properties of Metallic Parts Additively Manufactured through MEX and PBF-LB/M Technologies
por: Kluczyński, Janusz, et al.
Publicado: (2023)

Process Parameter Investigation and Torsional Strength Analysis of the Additively Manufactured 3D Structures Made of 20MnCr5 Steel
por: Sarzyński, Bartłomiej, et al.
Publicado: (2023)

Bending Strength of Polyamide-Based Composites Obtained during the Fused Filament Fabrication (FFF) Process
por: Mazurkiewicz, Michał, et al.
Publicado: (2022)

Performance Properties of Cement–Glass Composite Bricks (CGCB) with Additively Manufactured (AM) Polymeric Scaffolding
por: Małek, Marcin, et al.
Publicado: (2023)

Crack Growth Behavior of Additively Manufactured 316L Steel—Influence of Build Orientation and Heat Treatment
por: Kluczyński, Janusz, et al.
Publicado: (2020)

Modification of Structural Properties Using Process Parameters and Surface Treatment of Monolithic and Thin-Walled Parts Obtained by Selective Laser Melting
por: Grzelak, Krzysztof, et al.
Publicado: (2020)

Influence of Selective Laser Melting Technological Parameters on the Mechanical Properties of Additively Manufactured Elements Using 316L Austenitic Steel
por: Kluczyński, Janusz, et al.
Publicado: (2020)

Additive Manufacturing of Plastics Used for Protection against COVID19—The Influence of Chemical Disinfection by Alcohol on the Properties of ABS and PETG Polymers
por: Grzelak, Krzysztof, et al.
Publicado: (2021)

Selective Laser Melted M300 Maraging Steel—Material Behaviour during Ballistic Testing
por: Szachogłuchowicz, Ireneusz, et al.
Publicado: (2021)

Processability of 21NiCrMo2 Steel Using the Laser Powder Bed Fusion: Selection of Process Parameters and Resulting Mechanical Properties
por: Łuszczek, Jakub, et al.
Publicado: (2022)

Wear Analysis of Additively Manufactured Slipper-Retainer in the Axial Piston Pump
por: Klimek, Agnieszka, et al.
Publicado: (2022)

A Comparative Study on Laser Powder Bed Fusion of Differently Atomized 316L Stainless Steel
por: Grzelak, Krzysztof, et al.
Publicado: (2022)

The Examination of Restrained Joints Created in the Process of Multi-Material FFF Additive Manufacturing Technology
por: Kluczyński, Janusz, et al.
Publicado: (2020)

The Influence of Heat Treatment on Low Cycle Fatigue Properties of Selectively Laser Melted 316L Steel
por: Kluczyński, Janusz, et al.
Publicado: (2020)

Mechanical Properties Analysis of the AA2519-AA1050-Ti6Al4V Explosive Welded Laminate
por: Szachogluchowicz, Ireneusz, et al.
Publicado: (2020)

Comparison of Different Heat Treatment Processes of Selective Laser Melted 316L Steel Based on Analysis of Mechanical Properties
por: Kluczyński, Janusz, et al.
Publicado: (2020)

Microstructure and Mechanical Properties of Dissimilar Friction Stir Welded Joint AA7020/AA5083 with Different Joining Parameters
por: Torzewski, Janusz, et al.
Publicado: (2022)

The Influence of Exposure Energy Density on Porosity and Microhardness of the SLM Additive Manufactured Elements
por: Kluczyński, Janusz, et al.
Publicado: (2018)

A Critical Review on Effect of Process Parameters on Mechanical and Microstructural Properties of Powder-Bed Fusion Additive Manufacturing of SS316L
por: Gor, Meet, et al.
Publicado: (2021)

Research on the Properties and Low Cycle Fatigue of Sc-Modified AA2519-T62 FSW Joint
por: Kosturek, Robert, et al.
Publicado: (2020)

Microstructure and Low Cycle Fatigue Properties of AA5083 H111 Friction Stir Welded Joint
por: Torzewski, Janusz, et al.
Publicado: (2020)

Static and Dynamic Loading Behavior of Ti6Al4V Honeycomb Structures Manufactured by Laser Engineered Net Shaping (LENS(TM)) Technology
por: Antolak-Dudka, Anna, et al.
Publicado: (2019)

Influence of Fabrication Method and Surface Modification of Alumina Ceramic on the Microstructure and Mechanical Properties of Ceramic–Elastomer Interpenetrating Phase Composites (IPCs)
por: Kozera, Paulina, et al.
Publicado: (2022)

Physical and Mechanical Properties of Polypropylene Fibre-Reinforced Cement–Glass Composite
por: Małek, Marcin, et al.
Publicado: (2021)

The study of the roundness and cylindricity deviations of parts produced with the use of the additive manufacturing
por: Świderski, Jacek, et al.
Publicado: (2022)

Laser-Induced Graphene on Additive Manufacturing Parts
por: Jiao, Lishi, et al.
Publicado: (2019)

Deformation Process of 3D Printed Structures Made from Flexible Material with Different Values of Relative Density
por: Płatek, Paweł, et al.
Publicado: (2020)

3D Printing in the Fight Against Covid-19
por: Płatek, Paweł, et al.
Publicado: (2023)

Additive Manufacturing of Metallic Parts – Introduction into Technologies and Materials
por: Weissgärber, Thomas
Publicado: (2019)

Additive Manufacturing of Metallic Parts – Introduction into Technologies and Materials
por: Weissgärber, Thomas
Publicado: (2019)

On the Pin-Bearing Strength of Additively Manufactured Polymer Parts
por: Khosravani, Mohammad Reza, et al.
Publicado: (2023)

The Influence of Post-Weld Heat Treatment on the Microstructure and Fatigue Properties of Sc-Modified AA2519 Friction Stir-Welded Joint
por: Kosturek, Robert, et al.
Publicado: (2019)

Low Cycle Fatigue Properties of Sc-Modified AA2519-T62 Extrusion
por: Kosturek, Robert, et al.
Publicado: (2020)

Effect of Welding Parameters on Mechanical Properties and Microstructure of Friction Stir Welded AA7075-T651 Aluminum Alloy Butt Joints
por: Kosturek, Robert, et al.
Publicado: (2022)

Basic Design Parameters Influencing on Axial Stiffness of the Spiral Wound Gasket
por: Jaszak, Przemysław, et al.
Publicado: (2023)

The retroperitoneal, inguinal approach to distal part of the ureter
por: Urbanowicz, Wiesław, et al.
Publicado: (2014)

The Influence of Layer Thickness on the Microstructure and Mechanical Properties of M300 Maraging Steel Additively Manufactured by LENS(®) Technology
por: Rońda, Natalia, et al.
Publicado: (2022)

Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing
por: Mikulikova, Aleksandra, et al.
Publicado: (2023)

How Can We Provide Additively Manufactured Parts with a Fingerprint? A Review of Tagging Strategies in Additive Manufacturing
por: Sola, Antonella, et al.
Publicado: (2021)

Nanofunctionalization of Additively Manufactured Titanium Substrates for Surface-Enhanced Raman Spectroscopy Measurements
por: Pisarek, Marcin, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_qljs1426ou4fdrm5mv8et7qsje