Cargando…

Microstructural Changes and Determination of a Continuous Cooling Transformation (CCT) Diagram Using Dilatometric Analysis of M398 High-Alloy Tool Steel Produced by Microclean Powder Metallurgy

The paper deals with the dilatometric study of high-alloy martensitic tool steel with the designation M398 (BÖHLER), which is produced by the powder metallurgy process. These materials are used to produce screws for injection molding machines in the plastic industry. Increasing the life cycle of the...

Descripción completa

Detalles Bibliográficos
Autores principales:	Krbata, Michal, Ciger, Robert, Kohutiar, Marcel, Eckert, Maros, Barenyi, Igor, Trembach, Bohdan, Dubec, Andrej, Escherova, Jana, Gavalec, Matúš, Beronská, Naďa
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10301817/ https://www.ncbi.nlm.nih.gov/pubmed/37374656 http://dx.doi.org/10.3390/ma16124473

Ejemplares similares

Austenite Decomposition of a Lean Medium Mn Steel Suitable for Quenching and Partitioning Process: Comparison of CCT and DCCT Diagram and Their Microstructural Changes
por: Krbata, Michal, et al.
Publicado: (2022)

Effect of Supercritical Bending on the Mechanical & Tribological Properties of Inconel 625 Welded Using the Cold Metal Transfer Method on a 16Mo3 Steel Pipe
por: Krbata, Michal, et al.
Publicado: (2023)

Analysis of Tribological Properties of Powdered Tool Steels M390 and M398 in Contact with Al(2)O(3)
por: Studeny, Zbynek, et al.
Publicado: (2022)

The Effect of Rotary Friction Welding Conditions on the Microstructure and Mechanical Properties of Ti6Al4V Titanium Alloy Welds
por: Gavalec, Matúš, et al.
Publicado: (2023)

Effect of Selected Cooling and Deformation Parameters on the Structure and Properties of AISI 4340 Steel
por: Eckert, Maros, et al.
Publicado: (2020)

DMA Analysis of Plasma Modified PVC Films and the Nature of Initiated Surface Changes
por: Janík, Róbert, et al.
Publicado: (2022)

Dry Sliding Friction of Tool Steels and Their Comparison of Wear in Contact with ZrO(2) and X46Cr13
por: Krbata, Michal, et al.
Publicado: (2020)

Dilatometric and Microstructural Study of Martensite Tempering in 4% Mn Steel
por: Grajcar, Adam, et al.
Publicado: (2020)

A Dilatometric Study of Tempering Complemented by Mössbauer Spectroscopy and other Characterization Techniques
por: Vieira, I., et al.
Publicado: (2017)

Dilatometric Analysis of the Austenite Decomposition in Undeformed and Deformed Low-Carbon Structural Steel
por: Morawiec, Mateusz, et al.
Publicado: (2020)

Extended Continuous Cooling Transformation (CCT) Diagrams Determination for Additive Manufacturing Deposited Steels
por: Halmešová, Kristýna, et al.
Publicado: (2022)

Dilatometric Study of Phase Transformations in 5 Mn Steel Subjected to Different Heat Treatments
por: Morawiec, Mateusz, et al.
Publicado: (2020)

Dilatometric Analysis and Kinetics Research of Martensitic Transformation under a Temperature Gradient and Stress
por: Liu, Liheng, et al.
Publicado: (2021)

Determination of CCT Diagram by Dilatometry Analysis of High-Strength Low-Alloy S960MC Steel
por: Moravec, Jaromír, et al.
Publicado: (2022)

CCT and Cullin1 regulate the TORC1 pathway to promote dendritic arborization in health and disease
por: Lottes, Erin N., et al.
Publicado: (2023)

Effects of Austenitization Temperature and Pre-Deformation on CCT Diagrams of 23MnNiCrMo5-3 Steel
por: Schindler, Ivo, et al.
Publicado: (2020)

Estimation of Cooling Rate of High-Strength Thick Plate Steel during Water Quenching Based on a Dilatometric Experiment
por: Jo, Hyo-Haeng, et al.
Publicado: (2023)

Physical metallurgy /
por: Hosford, William F.
Publicado: (2010)

Mechanical metallurgy
por: Dieter, George Ellwood, 1928-
Publicado: (1976)

Mechanical metallurgy /
por: Dieter, George E., 1928-
Publicado: (1986)

The technology of metallurgy /
por: Dalton, William K.
Publicado: (1994)

Mechanical metallurgy
por: Dieter, George E
Publicado: (1988)

An introduction to metallurgy
por: Cottrell, Alan
Publicado: (1975)

Welding metallurgy
por: Kou, Sindo P
Publicado: (1987)

Metallurgy and fuels
por: Finniston, H M, et al.
Publicado: (1956)

Vacuum metallurgy
por: Bunshah, Rointan Framroze
Publicado: (1958)

Uranium metallurgy
por: Wilkinson, W D
Publicado: (1962)

Métallurgie spéciale
por: Herenguel, Jean
Publicado: (1962)

Dental Metallurgy
Publicado: (1882)

Address on Metallurgy
por: Leslie,
Publicado: (1859)

Dental Metallurgy
Publicado: (1911)

Ancient Metallurgy
por: Leffmann, Henry
Publicado: (1897)

Intra-individual diagnostic image quality and organ-specific-radiation dose comparison between spiral cCT with iterative image reconstruction and z-axis automated tube current modulation and sequential cCT
por: Wenz, Holger, et al.
Publicado: (2016)

Elements of structural metallurgy
por: Hume-Rothery, William
Publicado: (1961)

Metallurgy of superconducting materials
por: Luhman, Thomas, et al.
Publicado: (1979)

Introduction to physical metallurgy
por: Avner, Sidney H.
Publicado: (1964)

The principles of physical metallurgy
por: Doan, Gilbert Everett, 1897-1970
Publicado: (1953)

Metallurgie des Aluminiums
por: Beljaew, A I, et al.
Publicado: (1956)

Physical metallurgy principles
por: Abbaschian, Reza, et al.
Publicado: (2010)

Symposium on Vacuum Metallurgy
por: Collective
Publicado: (1961)

Cannot write session to /tmp/vufind_sessions/sess_v235k5sc5kk438kqgcg13uldmt