Cargando…

Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process

An experimental study of the abrasive water jet cutting process of Inconel 718 alloy samples with varying values of cutting speed, abrasive flow rate and cutting material height was carried out. Surface roughness and waviness were measured at different cutting depths, and the variation of the kerf a...

Descripción completa

Detalles Bibliográficos
Autores principales:	Płodzień, Marcin, Żyłka, Łukasz, Żak, Krzysztof, Wojciechowski, Szymon
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10420035/ https://www.ncbi.nlm.nih.gov/pubmed/37569993 http://dx.doi.org/10.3390/ma16155288

Ejemplares similares

High-Performance Face Milling of 42CrMo4 Steel: Influence of Entering Angle on the Measured Surface Roughness, Cutting Force and Vibration Amplitude
por: Płodzień, Marcin, et al.
Publicado: (2021)

Analysis of Kerf Quality Characteristics of Kevlar Fiber-Reinforced Polymers Cut by Abrasive Water Jet
por: Gubencu, Dinu-Valentin, et al.
Publicado: (2023)

Influence of Variable Radius of Cutting Head Trajectory on Quality of Cutting Kerf in the Abrasive Water Jet Process for Soda–Lime Glass
por: Sutowska, Marzena, et al.
Publicado: (2020)

Experimental Analysis of Kerf Taper Angle in Cutting Process of Sugar Palm Fiber Reinforced Unsaturated Polyester Composites with Laser Beam and Abrasive Water Jet Cutting Technologies
por: Masoud, Fathi, et al.
Publicado: (2021)

Comparison of Flank Super Abrasive Machining vs. Flank Milling on Inconel(®) 718 Surfaces
por: González, Haizea, et al.
Publicado: (2018)

Cutting Forces during Inconel 718 Orthogonal Turn-Milling
por: Felusiak-Czyryca, Agata, et al.
Publicado: (2021)

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM
por: Shen, Qi, et al.
Publicado: (2018)

Study on the Effects of Different Cutting Angles on the End-Milling of Wire and Arc Additive Manufacturing Inconel 718 Workpieces
por: dos Santos, Gustavo Quadra Vieira, et al.
Publicado: (2022)

Modeling and Prediction of Water-Jet-Guided Laser Cutting Depth for Inconel 718 Material Using Response Surface Methodology
por: Zhao, Chuang, et al.
Publicado: (2023)

An Investigation of the Work Hardening Behavior in Interrupted Cutting Inconel 718 under Cryogenic Conditions
por: Dai, Xing, et al.
Publicado: (2020)

Prediction of Surface Roughness of an Abrasive Water Jet Cut Using an Artificial Neural Network
por: Ficko, Mirko, et al.
Publicado: (2021)

Influence of Microgroove Structure on Cutting Performance and Chip Morphology during the Turning of Superalloy Inconel 718
por: Zou, Zhongfei, et al.
Publicado: (2021)

Effect of Ball Burnishing Pressure on Surface Roughness by Low Plasticity Burnishing Inconel 718 Pre-Turned Surface
por: Cui, Pengcheng, et al.
Publicado: (2022)

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718
por: Wang, Bing, et al.
Publicado: (2018)

Coating-thickness-dependent physical properties and cutting temperature for cutting Inconel 718 with TiAlN coated tools
por: Zhao, Jinfu, et al.
Publicado: (2021)

Effect of silicon carbide on kerf convergence and irregularity of the surface during abrasive water jet machining of fiber-metal hybrid composites
por: Selvam, R., et al.
Publicado: (2023)

Temperature Measurement and Numerical Prediction in Machining Inconel 718
por: Díaz-Álvarez, José, et al.
Publicado: (2017)

Selective Anisotropy of Mechanical Properties in Inconel718 Alloy
por: Liang, Yu, et al.
Publicado: (2021)

Achieving the Minimum Roughness of Laser Milled Micro-Impressions on Ti 6Al 4V, Inconel 718, and Duralumin
por: Ahmed, Naveed, et al.
Publicado: (2020)

Influence of reduced graphene oxide addition on kerf width in abrasive water jet machining of nanofiller added epoxy-glass fibre composite
por: V., Kavimani, et al.
Publicado: (2022)

Factorial Analysis of Fiber Laser Fusion Cutting of AISI 304 Stainless Steel: Evaluation of Effects on Process Performance, Kerf Geometry and Cut Edge Roughness
por: Mahrle, Achim, et al.
Publicado: (2021)

Optimization of Cutting Process Parameters in Inclined Drilling of Inconel 718 Using Finite Element Method and Taguchi Analysis
por: Pervaiz, Salman, et al.
Publicado: (2020)

Study of the Effects of Initial Cutting Conditions and Transition Period on Ultimate Tool Life when Machining Inconel 718
por: Memarianpour, Morvarid, et al.
Publicado: (2021)

Impact of Notches on Additively Manufactured Inconel 718 Tensile Performance
por: Johnson, Joseph, et al.
Publicado: (2023)

Modelling of the Face-Milling Process by Toroidal Cutter
por: Płodzień, Marcin, et al.
Publicado: (2023)

Prediction of Kerf Width and Surface Roughness of Al6351 Based Composite in Wire-Cut Electric Discharge Machining Using Mathematical Modelling
por: Sree Ram, Hariharan, et al.
Publicado: (2022)

Investigation of Cutting Temperature during Turning Inconel 718 with (Ti,Al)N PVD Coated Cemented Carbide Tools
por: Zhao, Jinfu, et al.
Publicado: (2018)

A Novel Flushing Mechanism to Minimize Roughness and Dimensional Errors during Wire Electric Discharge Machining of Complex Profiles on Inconel 718
por: Farooq, Muhammad Umar, et al.
Publicado: (2022)

Grain Refinement of Inconel 718 Superalloy—The Effect of Rotating Magnetic Field
por: Silva, Rui Pedro, et al.
Publicado: (2022)

Measuring the effect of residual stress on the machined subsurface of Inconel 718 by nanoindentation
por: Chen, Ling, et al.
Publicado: (2021)

Deformation Analysis of Continuous Milling of Inconel718 Nickel-Based Superalloy
por: Li, Xueguang, et al.
Publicado: (2022)

In Envelope Additive/Subtractive Manufacturing and Thermal Post-Processing of Inconel 718
por: Atabay, Sila Ece, et al.
Publicado: (2022)

Surface Topography Description of Threads Made with Turning on Inconel 718 Shafts
por: Krawczyk, Bartłomiej, et al.
Publicado: (2022)

High temperature performance of wire-arc additive manufactured Inconel 718
por: James, William Sean, et al.
Publicado: (2023)

Milling Mechanism and Chattering Stability of Nickel-Based Superalloy Inconel 718
por: Zheng, Jin, et al.
Publicado: (2023)

Simulation of Work Hardening in Machining Inconel 718 with Multiscale Grain Size
por: Zhuang, Kejia, et al.
Publicado: (2023)

A Study of the Kinematics System in Drilling Inconel 718 for Improving of Hole Quality in the Aviation and Space Industries
por: Bronis, Mateusz, et al.
Publicado: (2022)

Study of the Influence of Shielding Gases on Laser Metal Deposition of Inconel 718 Superalloy
por: Ruiz, Jose Exequiel, et al.
Publicado: (2018)

An Investigation of Surface Corrosion Behavior of Inconel 718 after Robotic Belt Grinding
por: Wang, Junwei, et al.
Publicado: (2018)

Analysis of the Machining Process of Inconel 718 Parts Manufactured by Laser Metal Deposition
por: Ostra, Txomin, et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_vhm3prt2rf101d66kg8epcsjtg