Cargando…

Solid-State Transformation of an Additive Manufactured Inconel 625 Alloy at 700 °C

Inconel 625, a nickel-based superalloy, has drawn much attention in the emerging field of additive manufacturing (AM) because of its excellent weldability and resistance to hot cracking. The extreme processing condition of AM often introduces enormous residual stress (hundreds of MPa to GPa) in the...

Descripción completa

Detalles Bibliográficos
Autores principales:	Zhang, Fan, Ilavsky, Jan, Lindwall, Greta, Stoudt, Mark R., Levine, Lyle E., Allen, Andrew J.
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	2021
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10426615/ https://www.ncbi.nlm.nih.gov/pubmed/37583437 http://dx.doi.org/10.3390/app11188643

Ejemplares similares

Simulation of TTT Curves for Additively Manufactured Inconel 625
por: LINDWALL, G., et al.
Publicado: (2019)

Precipitates in Additively Manufactured Inconel 625 Superalloy
por: Dubiel, Beata, et al.
Publicado: (2019)

Heating Conditions Influence on Solidification of Inconel 625–WC System for Additive Manufacturing
por: Huebner, Jan, et al.
Publicado: (2020)

The Interface Microstructures and Mechanical Properties of Laser Additive Repaired Inconel 625 Alloy
por: Wei, Yiyun, et al.
Publicado: (2020)

Investigation of microstructure in additive manufactured Inconel 625 by spatially resolved neutron transmission spectroscopy
por: Tremsin, Anton S., et al.
Publicado: (2016)

High Strain Rate Yielding of Additive Manufacturing Inconel 625 by Selective Laser Melting
por: Du, Kang, et al.
Publicado: (2021)

Mechanical and Microstructural Characterization of Arc-Welded Inconel 625 Alloy
por: Kotzem, Daniel, et al.
Publicado: (2019)

Towards Automatic Detection of Precipitates in Inconel 625 Superalloy Additively Manufactured by the L-PBF Method
por: Macioł, Piotr, et al.
Publicado: (2021)

Stress Corrosion Cracking of Additively Manufactured Alloy 625
por: Cabrini, Marina, et al.
Publicado: (2021)

Parametric Optimization of Laser Additive Manufacturing of Inconel 625 Using Taguchi Method and Grey Relational Analysis
por: Yang, Bo, et al.
Publicado: (2020)

The temperature dependence of the surface composition of Inconel 600 and Inconel 625
por: Achard, M H, et al.
Publicado: (1976)

Effect of Fe Content on Microstructure and Properties of Laser Cladding Inconel 625 Alloy
por: Liu, Weidong, et al.
Publicado: (2022)

Study of the Dynamic Recrystallization Process of the Inconel625 Alloy at a High Strain Rate
por: Jia, Zhi, et al.
Publicado: (2019)

Investigation into the Microstructure and Hardness of Additively Manufactured (3D-Printed) Inconel 718 Alloy
por: Kurdi, Abdulaziz, et al.
Publicado: (2023)

Ultrasonic Sensor Signals and Optimum Path Forest Classifier for the Microstructural Characterization of Thermally-Aged Inconel 625 Alloy
por: de Albuquerque, Victor Hugo C., et al.
Publicado: (2015)

Thermal Processing Map and Microstructure Evolution of Inconel 625 Alloy Sheet Based on Plane Strain Compression Deformation
por: Song, Yuelin, et al.
Publicado: (2021)

Effect of MBF-20 Interlayer on the Microstructure and Corrosion Behaviour of Inconel 625 Super Alloy after Diffusion Brazing
por: Doroudi, Alireza, et al.
Publicado: (2023)

Developing Creep and Stress Relaxation Models to Assess the Service Life of an Additive Manufactured Industrial-Scale Recuperator Utilizing Inconel 625 and AISI 310S Materials
por: Papalexis, Christos, et al.
Publicado: (2023)

FEM-Based Thermogram Correction for Inconel 625 Joint Hardness Clustering
por: Jamrozik, Wojciech, et al.
Publicado: (2022)

Investigation of Strain Fatigue Behavior for Inconel 625 with Laser Shock Peening
por: Sun, Yaofei, et al.
Publicado: (2022)

Tensile Notch Sensitivity of Additively Manufactured IN 625 Superalloy
por: Matache, Gheorghe, et al.
Publicado: (2020)

Effect of Iron Ion on Corrosion Behavior of Inconel 625 in High-Temperature Water
por: Zhou, Huiling, et al.
Publicado: (2020)

The Structure and Properties of Laser-Cladded Inconel 625/TiC Composite Coatings
por: Poloczek, Tomasz, et al.
Publicado: (2023)

Impact of Notches on Additively Manufactured Inconel 718 Tensile Performance
por: Johnson, Joseph, et al.
Publicado: (2023)

Interface Analysis between Inconel 625 and Cobalt-Chromium Alloy Fabricated by Powder Bed Fusion Using Pulsed Wave Laser
por: Yao, Liming, et al.
Publicado: (2023)

The surface properties of Inconel 600 and Inconel 625 studied by Scanning Electron Microscopy, Auger Electron Spectroscopy and Ion Induced Desorption
por: Mathewson, A G
Publicado: (1976)

Influence of Building Direction on the Oxidation Behavior of Inconel 718 Alloy Fabricated by Additive Manufacture of Electron Beam Melting
por: Li, Lv, et al.
Publicado: (2018)

Grain-Boundary Interaction between Inconel 625 and WC during Laser Metal Deposition
por: Huebner, Jan, et al.
Publicado: (2018)

Fretting wear behavior of Inconel 718 alloy manufactured by DED and treated by UNSM
por: Li, Chao, et al.
Publicado: (2023)

In Envelope Additive/Subtractive Manufacturing and Thermal Post-Processing of Inconel 718
por: Atabay, Sila Ece, et al.
Publicado: (2022)

High temperature performance of wire-arc additive manufactured Inconel 718
por: James, William Sean, et al.
Publicado: (2023)

Assessment of Additive Manufactured IN 625’s Tensile Strength Based on Nonstandard Specimens
por: Paraschiv, Alexandru, et al.
Publicado: (2023)

Influence of solidification structure on austenite to martensite transformation in additively manufactured hot-work tool steels
por: Chou, Chia-Ying, et al.
Publicado: (2021)

Comparison of the Structure, Mechanical Properties and Effect of Heat Treatment on Alloy Inconel 718 Produced by Conventional Technology and by Additive Layer Manufacturing
por: Švec, Martin, et al.
Publicado: (2023)

SEM/TEM Investigation of Aluminide Coating Co-Doped with Pt and Hf Deposited on Inconel 625
por: Morgiel, Jerzy, et al.
Publicado: (2018)

Microstructure and Properties of Inconel 625 Fabricated Using Two Types of Laser Metal Deposition Methods
por: Dutkiewicz, Jan, et al.
Publicado: (2020)

Suitability of Laser Engineered Net Shaping Technology for Inconel 625 Based Parts Repair Process
por: Barwinska, Izabela, et al.
Publicado: (2021)

Application of Additively Manufactured Pentamode Metamaterials in Sodium/Inconel 718 Heat Pipes
por: Hu, Longfei, et al.
Publicado: (2021)

Influence of Selective Laser Melting Additive Manufacturing Parameters in Inconel 718 Superalloy
por: Kladovasilakis, Nikolaos, et al.
Publicado: (2022)

Development of Micro Laser Powder Bed Fusion for Additive Manufacturing of Inconel 718
por: Khademzadeh, Saeed, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_l7bei7l4kuufpbmidk54nkqafd