Cargando…

Continuous Extrusion Forming Technology of Magnesium Alloy Thin-Walled Tubules

This paper proposes a new technology of superimposed billet extrusion-forming for thin-walled magnesium alloy tubes. This process represents an improvement over the current technology, which suffers from low production efficiency, poor forming accuracy, and low material utilization. We developed a d...

Descripción completa

Detalles Bibliográficos
Autores principales:	Yang, Xi, Sun, Shihan, Zhou, Zheng, Chen, Xuewen, Chen, Guoqing
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10488630/ https://www.ncbi.nlm.nih.gov/pubmed/37687500 http://dx.doi.org/10.3390/ma16175803

Ejemplares similares

Effect of Zn and Mg Content on Crashworthiness of Al-Zn-Mg Alloy Thin-Walled Square Extrusions
por: Guo, Hui, et al.
Publicado: (2020)

Numerical Simulation and Experimental Analysis of the Semi-Solid Thixotropic Extrusion Forming Process for Producing the Thin-Wall Wrought Aluminum Alloy Mobile Phone Shells
por: Guo, Yi, et al.
Publicado: (2021)

AZ31 Magnesium Alloy Foils as Thin Anodes for Rechargeable Magnesium Batteries
por: Maddegalla, Ananya, et al.
Publicado: (2021)

Asymmetric Extrusion Technology of Mg Alloy: A Review
por: Yang, Qingshan, et al.
Publicado: (2023)

Extrusion Characteristics of Thin Walled Tubes for Catheters Using Thermoplastic Elastomer
por: Cho, Soonmo, et al.
Publicado: (2020)

Technologies for Joining and Forming Thin-Walled Structures in the Construction of Transportation Vehicles
por: Fydrych, Dariusz, et al.
Publicado: (2023)

Reactive Extrusion and Magnesium (II) N-Heterocyclic Carbene Catalyst in Continuous PLA Production
por: Mincheva, Rosica, et al.
Publicado: (2019)

Influence of Rare Earth Element (Y) on Microstructure and Corrosion Behavior of Hot Extrusion AZ91 Magnesium Alloy
por: Cui, Yanan, et al.
Publicado: (2020)

Correlation between dynamic recrystallization and formation of rare earth texture in a Mg-Zn-Gd magnesium alloy during extrusion
por: Jiang, M. G., et al.
Publicado: (2018)

In vitro corrosion of pure magnesium and AZ91 alloy—the influence of thin electrolyte layer thickness
por: Zeng, Rong-Chang, et al.
Publicado: (2016)

Effect of the Second Phases on Composite Spinning-Extrusion Forming and Mechanical Properties of Al–Cu–Li Alloy
por: Zeng, Huaqiang, et al.
Publicado: (2023)

Heat Treatment of AZ91 Magnesium Alloy Coated with an Al(2)O(3) Thin Film with Fluidized Bed Technology
por: Baiocco, Gabriele, et al.
Publicado: (2019)

Axoplasmic free magnesium levels and magnesium extrusion from squid giant axons
Publicado: (1976)

Influence of Process Parameters on the Height and Performance of Magnesium Alloy AZ91D Internal Thread by Assisted Heating Extrusion
por: Liu, Meng, et al.
Publicado: (2022)

Large Cutting Depth and Layered Milling of Titanium Alloy Thin-Walled Parts
por: Zha, Jun, et al.
Publicado: (2020)

Opportunities of combinatorial thin film materials design for the sustainable development of magnesium-based alloys
por: Hans, Marcus, et al.
Publicado: (2021)

A Calculation Model for Cooling Rate of Aluminum Alloy Melts during Continuous Rheo-Extrusion
por: Wang, Yu, et al.
Publicado: (2021)

Forming Limit Analysis of Thin-Walled Extruded Aluminum Alloy Tubes under Nonlinear Loading Paths Using an Improved M-K Model
por: Zhu, Haihui, et al.
Publicado: (2023)

Sodium and magnesium in the distal convoluted tubule: no longer a couple?
por: Rodan, Aylin R.
Publicado: (2018)

Finite Element Analysis of Extrusion Process for Magnesium Alloy Internal Threads with Electromagnetic Induction-Assisted Heating and Thread Performance Research
por: Liu, Meng, et al.
Publicado: (2020)

Influence of Extrusion Rate on Microstructure and Mechanical Properties of Magnesium Alloy AM60 and an AM60-Based Metal Matrix Nanocomposite
por: Giannopoulou, Danai, et al.
Publicado: (2022)

On the Performance of Thin-Walled Crash Boxes Joined by Forming
por: Silva, Diogo F. M., et al.
Publicado: (2018)

Microstructure Evolution Mechanism of Ultra-Thin Dual Phase Magnesium–Lithium Alloy during Asymmetric Warm Rolling
por: An, Shuang, et al.
Publicado: (2022)

Research Progress on Microstructure Evolution and Strengthening-Toughening Mechanism of Mg Alloys by Extrusion
por: Zheng, Yaqi, et al.
Publicado: (2023)

Analysis of the Extrusion Process of Aluminium Alloy Profiles
por: Bajor, Teresa, et al.
Publicado: (2022)

Pharmaceutical extrusion technology /
Publicado: (2003)

Guidebook to extrusion technology
por: Cheremisinoff, Nicholas P
Publicado: (1993)

Mechanisms coupling sodium and magnesium reabsorption in the distal convoluted tubule of the kidney
por: Franken, Gijs A. C., et al.
Publicado: (2020)

Crashworthiness Optimization Design of Aluminum Alloy Thin-Walled Triangle Column Based on Bioinspired Strategy
por: Li, Kangjie, et al.
Publicado: (2020)

Head Loss in Thin-Walled Drip Tapes with Continuous Labyrinth
por: Melo, Verônica G. M. L., et al.
Publicado: (2019)

Thin-Wall Machining of Light Alloys: A Review of Models and Industrial Approaches
por: Del Sol, Irene, et al.
Publicado: (2019)

Effect of the Geometry of Thin-Walled Aluminium Alloy Elements on Their Deformations after Milling
por: Zawada-Michałowska, Magdalena, et al.
Publicado: (2022)

Wrinkling and Strengthening Behaviors in the Two-Layer-Sheet Hot-Forming–Quenching Integrated Process for an Al–Cu–Mg-Alloy Thin-Walled Curved-Surface Shell
por: Fan, Xiaobo, et al.
Publicado: (2023)

Advances and Trends in Forming Curved Extrusion Profiles
por: Zhou, Wenbin, et al.
Publicado: (2021)

Influence of Pre-Heat Treatment on the Deformation Behaviors, Microstructural Characteristics, and Mechanical Properties of a Continuously Cast Al-Cu-Mg Alloy during Continuous Extrusion Process
por: Qin, Renbao, et al.
Publicado: (2023)

Enhanced Stretch Formability of AZ31 Magnesium Alloy Thin Sheet by Induced Precompression and Sequent Annealing
por: Wang, Lifei, et al.
Publicado: (2018)

Perspectives of Microstructure Refinement of Aluminum and Its Alloys by the Reciprocating Extrusion (Cyclic Extrusion Compression—CEC)
por: Richert, Maria, et al.
Publicado: (2022)

Additive manufacturing of magnesium alloys
por: Karunakaran, Rakeshkumar, et al.
Publicado: (2020)

Lean Wrought Magnesium Alloys
por: Papenberg, Nikolaus P., et al.
Publicado: (2021)

Microstructure and Texture Evolution of AZ31 Alloy Prepared by Cyclic Expansion Extrusion with Asymmetrical Extrusion Cavity at Different Temperatures
por: Zheng, Jie, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_habndhdo02higsppde2jlfn6fd