Cargando…

Virtual Coriolis-Force-Based Mode-Matching Micromachine-Optimized Tuning Fork Gyroscope without a Quadrature-Nulling Loop

A VCF-based mode-matching micromachine-optimized tuning fork gyroscope is proposed to not only maximize the scale factor of the device, but also avoid use of an additional quadrature-nulling loop to prevent structure complexity, pick-up electrode occupation, and coupling with a mode-matching loop. I...

Descripción completa

Detalles Bibliográficos
Autores principales:	Wu, Yixuan, Yuan, Weizheng, Xue, Yanjun, Chang, Honglong, Shen, Qiang
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10537024/ https://www.ncbi.nlm.nih.gov/pubmed/37763867 http://dx.doi.org/10.3390/mi14091704

Ejemplares similares

Optically read Coriolis vibratory gyroscope based on a silicon tuning fork
por: Lavrik, N. V., et al.
Publicado: (2019)

Z-Axis Micromachined Tuning Fork Gyroscope with Low Air Damping
por: Nguyen, Minh Ngoc, et al.
Publicado: (2017)

Automatic Mode-Matching Method for MEMS Disk Resonator Gyroscopes Based on Virtual Coriolis Force
por: Ruan, Zhihu, et al.
Publicado: (2020)

Micromachined Vibrating Ring Gyroscope Architecture with High-Linearity, Low Quadrature Error and Improved Mode Ordering
por: Li, Zezhang, et al.
Publicado: (2020)

Vibration Sensitivity Reduction of Micromachined Tuning Fork Gyroscopes through Stiffness Match Method with Negative Electrostatic Spring Effect
por: Guan, Yanwei, et al.
Publicado: (2016)

A Multi-Fork Z-Axis Quartz Micromachined Gyroscope
por: Feng, Lihui, et al.
Publicado: (2013)

Coriolis vibratory gyroscopes: theory and design
por: Apostolyuk, Vladislav
Publicado: (2016)

On Bandwidth Characteristics of Tuning Fork Micro-Gyroscope with Mechanically Coupled Sense Mode
por: Ni, Yunfang, et al.
Publicado: (2014)

Influence of Electrostatic Forces on the Vibrational Characteristics of Resonators for Coriolis Vibratory Gyroscopes
por: Xiao, Pengbo, et al.
Publicado: (2020)

A Z-Axis Quartz Cross-Fork Micromachined Gyroscope Based on Shear Stress Detection
por: Xie, Liqiang, et al.
Publicado: (2010)

Three-Dimensional Performance Evaluation of Hemispherical Coriolis Vibratory Gyroscopes
por: Mahmoudian, Mehrdad, et al.
Publicado: (2023)

Damping Asymmetry Trimming Based on the Resistance Heat Dissipation for Coriolis Vibratory Gyroscope in Whole-Angle Mode
por: Guo, Kechen, et al.
Publicado: (2020)

Vibration-Induced Errors in MEMS Tuning Fork Gyroscopes with Imbalance
por: Fang, Xiang, et al.
Publicado: (2018)

Effect of Quadrature Control Mode on ZRO Drift of MEMS Gyroscope and Online Compensation Method
por: Bu, Feng, et al.
Publicado: (2022)

Characterization of Modal Frequencies and Orientation of Axisymmetric Resonators in Coriolis Vibratory Gyroscopes
por: Ding, Xukai, et al.
Publicado: (2021)

A Novel Self-Calibration Method and Experiment of MEMS Gyroscope Based on Virtual Coriolis Force
por: Wang, Minruihong, et al.
Publicado: (2018)

Automatic Frequency Tuning Technology for Dual-Mass MEMS Gyroscope Based on a Quadrature Modulation Signal
por: Jia, Jia, et al.
Publicado: (2018)

A Tuning Fork Gyroscope with a Polygon-Shaped Vibration Beam
por: Xu, Qiang, et al.
Publicado: (2019)

Design and Optimization of a Novel MEMS Tuning Fork Gyroscope Microstructure
por: Xiong, Chuanguo, et al.
Publicado: (2022)

Effect of Axial Force on the Performance of Micromachined Vibratory Rate Gyroscopes
por: Hou, Zhanqiang, et al.
Publicado: (2010)

A Lumped Mass Model for Circular Micro-Resonators in Coriolis Vibratory Gyroscopes
por: Ding, Xukai, et al.
Publicado: (2019)

The Development of Micromachined Gyroscope Structure and Circuitry Technology
por: Xia, Dunzhu, et al.
Publicado: (2014)

Two Novel Measurements for the Drive-Mode Resonant Frequency of a Micromachined Vibratory Gyroscope
por: Wang, Ancheng, et al.
Publicado: (2013)

Design, Dynamics, and Optimization of a 3-DoF Nonlinear Micro-Gyroscope by Considering the Influence of the Coriolis Force
por: Wang, Sai, et al.
Publicado: (2022)

Design and Application of Quadrature Compensation Patterns in Bulk Silicon Micro-Gyroscopes
por: Ni, Yunfang, et al.
Publicado: (2014)

The Effect of Displacement Constraints on the Failure of MEMS Tuning Fork Gyroscopes under Shock Impact
por: Lian, Jiangkai, et al.
Publicado: (2019)

Influence of Temperature Variation on the Vibrational Characteristics of Fused Silica Cylindrical Resonators for Coriolis Vibratory Gyroscopes
por: Xiao, Pengbo, et al.
Publicado: (2020)

A Digital Calibration Technique of MEMS Gyroscope for Closed-Loop Mode-Matching Control
por: Li, Cheng, et al.
Publicado: (2019)

An Integrated MEMS Gyroscope Array with Higher Accuracy Output
por: Chang, Honglong, et al.
Publicado: (2008)

Optimization and Experimentation of Dual-Mass MEMS Gyroscope Quadrature Error Correction Methods
por: Cao, Huiliang, et al.
Publicado: (2016)

Design of Readout Circuit with Quadrature Error and Auxiliary PLL for MEMS Vibratory Gyroscope
por: Chen, Hua, et al.
Publicado: (2020)

Analysis of Frequency Response and Scale-Factor of Tuning Fork Micro-Gyroscope Operating at Atmospheric Pressure
por: Ding, Xukai, et al.
Publicado: (2015)

Design and Mechanical Sensitivity Analysis of a MEMS Tuning Fork Gyroscope with an Anchored Leverage Mechanism
por: Li, Zezhang, et al.
Publicado: (2019)

Decoupling Control of Micromachined Spinning-Rotor Gyroscope with Electrostatic Suspension
por: Sun, Boqian, et al.
Publicado: (2016)

Spin Rate Effects in a Micromachined Electrostatically Suspended Gyroscope
por: Sun, Boqian, et al.
Publicado: (2018)

Real-Time Built-In Self-Test of MEMS Gyroscope Based on Quadrature Error Signal
por: Feng, Rui, et al.
Publicado: (2021)

The Effect of the Bending Beam Width Variations on the Discrepancy of the Resulting Quadrature Errors in MEMS Gyroscopes
por: Azier, Alexandre, et al.
Publicado: (2022)

Design and Vibration Sensitivity Analysis of a MEMS Tuning Fork Gyroscope with an Anchored Diamond Coupling Mechanism
por: Guan, Yanwei, et al.
Publicado: (2016)

Design, Fabrication, and Testing of a Bulk Micromachined Inertial Measurement Unit
por: Chang, Honglong, et al.
Publicado: (2010)

Design of a Tri-Axial Surface Micromachined MEMS Vibrating Gyroscope
por: Crescenzi, Rocco, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_ned7f2vnqh6epp6hocoetik6oj