Cargando…

Water Sorption in Hybrid Polyester/Glass/Jute Composites Processed via Compression Molding and Vacuum-Assisted Resin Transfer Molding

The aim of this work is to analyze water sorption in hybrid polyester/glass fabric/jute fabric composites molded via compression and VARTM (Vacuum-Assisted Resin Transfer Molding). The laminates were produced with five different stacking sequences and subjected to water sorption testing at room temp...

Descripción completa

Detalles Bibliográficos
Autores principales:	Aranha, Rudá, Filho, Mario A. Albuquerque, de Lima Santos, Cícero, Fonseca, Viviane M., Rivera, José L. V., de Lima, Antonio G. B., de Amorim, Wanderley F., Carvalho, Laura H.
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2023
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC10675004/ https://www.ncbi.nlm.nih.gov/pubmed/38006161 http://dx.doi.org/10.3390/polym15224438

Ejemplares similares

Transferability of Diffractive Structure in the Compression Molding of Chalcogenide Glass
por: Son, Byeong-Rea, et al.
Publicado: (2023)

Reproducibility Study of the Thermoplastic Resin Transfer Molding Process for Glass Fiber Reinforced Polyamide 6 Composites †
por: Martins, Filipe P., et al.
Publicado: (2023)

Pre-Compensation of Mold in Precision Glass Molding Based on Mathematical Analysis
por: Zhang, Yue, et al.
Publicado: (2020)

Development of an Injection Molding Process for Long Glass Fiber-Reinforced Phenolic Resins
por: Maertens, Robert, et al.
Publicado: (2022)

Investigation of the Viscoelastic Behavior Variation of Glass Mat Thermoplastics (GMT) in Compression Molding
por: Huang, Chao-Tsai, et al.
Publicado: (2019)

Preparation of Glass Fabric/Poly(l-lactide) Composites by Thermoplastic Resin Transfer Molding
por: Louisy, Elodie, et al.
Publicado: (2019)

A Comprehensive Review of Micro/Nano Precision Glass Molding Molds and Their Fabrication Methods
por: Asgar, Md. Ali, et al.
Publicado: (2021)

Resin Flow Behavior Simulation of Grooved Foam Sandwich Composites with the Vacuum Assisted Resin Infusion (VARI) Molding Process
por: Zhao, Chenhui, et al.
Publicado: (2012)

Development and Validation of a Test Mold for Thermoplastic Resin Transfer Molding of Reactive PA-6
por: Boros, Róbert, et al.
Publicado: (2020)

Thioetherimide-Modified Cyanate Ester Resin with Better Molding Performance for Glass Fiber Reinforced Composites
por: Ma, Pengchang, et al.
Publicado: (2019)

Modeling fracture behavior in precision glass molding
por: Liu, Gang
Publicado: (2018)

Thermomechanical Behavior of Molded Metallic Glass Nanowires
por: Magagnosc, Daniel J., et al.
Publicado: (2016)

Preparation of High-Performance Carbon Fiber-Reinforced Epoxy Composites by Compression Resin Transfer Molding
por: Sun, Zeyu, et al.
Publicado: (2018)

Fabricating Microstructures on Glass for Microfluidic Chips by Glass Molding Process
por: Wang, Tao, et al.
Publicado: (2018)

Use of Multi-Hollow Polyester Particles as Opacifying Agent for Injection-Molded Polyethylene
por: F. A. Silva, João, et al.
Publicado: (2020)

Direct In-Mold Impregnation of Glass Fiber Fabric by Polypropylene with Supercritical Nitrogen in Microcellular Injection Molding Process
por: He, Qichao, et al.
Publicado: (2023)

Comparison of Conventional Pressure-packed and Injection Molding Processing Methods for an Acrylic Resin Denture based on Microhardness, Surface Roughness, and Water Sorption
por: Moslehifard, Elnaz, et al.
Publicado: (2022)

Vacuum Compression Molding as a Screening Tool to Investigate Carrier Suitability for Hot-Melt Extrusion Formulations
por: Shadambikar, Gauri, et al.
Publicado: (2020)

Manufacturing Signatures of Injection Molding and Injection Compression Molding for Micro-Structured Polymer Fresnel Lens Production
por: Loaldi, Dario, et al.
Publicado: (2018)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

Using a Fiber Bragg Grating Sensor to Measure Residual Strain in the Vacuum-Assisted Resin Transfer Molding Process
por: Luo, Guang-Min, et al.
Publicado: (2022)

Transport phenomena in liquid composite molding processes
por: Delgado, João M P Q, et al.
Publicado: (2019)

Wear resistance of injection-molded thermoplastic denture base resins
por: Hamanaka, Ippei, et al.
Publicado: (2016)

Injection Compression Molded Microlens Arrays for Hyperspectral Imaging
por: Roeder, Marcel, et al.
Publicado: (2018)

Comparative evaluation of flexural strength of denture base resin materials processed using compression molding technique, injection molding technique, and computer-aided design CAM technique: An in vitro study
por: Patankar, Rutika C., et al.
Publicado: (2022)

Study the Formation Process of Cuboid Microprotrusion by Glass Molding Process †
por: Wang, Tao, et al.
Publicado: (2017)

Optimizing Glass Fiber Molding Process Design by Reverse Warping
por: Chang, Han-Jui, et al.
Publicado: (2020)

Effect of mold treatment by solvent on PDMS molding into nanoholes
por: Con, Celal, et al.
Publicado: (2013)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Mechanical Properties of Boehmeria nivea Natural Fabric Reinforced Epoxy Matrix Composite Prepared by Vacuum-Assisted Resin Infusion Molding
por: Garcia Filho, Fabio da Costa, et al.
Publicado: (2020)

A Review of Thermoplastic Resin Transfer Molding: Process Modeling and Simulation
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Research on Anisotropic Viscoelastic Constitutive Model of Compression Molding for CFRP
por: Xie, Jiuming, et al.
Publicado: (2020)

A Review of the Precision Glass Molding of Chalcogenide Glass (ChG) for Infrared Optics
por: Zhou, Tianfeng, et al.
Publicado: (2018)

Molds and the lungs
por: Sharma, Bharat Bhushan
Publicado: (2010)

Molded Optics
por: Schaub, Michael, et al.
Publicado: (2016)

Self-Extinguishing Resin Transfer Molding Composites Using Non-Fire-Retardant Epoxy Resin
por: Geng, Zhi, et al.
Publicado: (2018)

In-Mold Sensors for Injection Molding: On the Way to Industry 4.0
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

Increasing Impact Strength of a Short Glass Fiber Compression Molded BMC by Shortening Fibers without Change in Equipment
por: Faudree, Michael C., et al.
Publicado: (2022)

Micro-Scale Vacuum Compression Molding as a Predictive Screening Tool of Protein Integrity for Potential Hot-Melt Extrusion Processes
por: Dauer, Katharina, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_fumcnup305sk1r3melribtc4lv