Cargando…

Acoustic Performance of 3D Printed Nanocomposite Earmuff

INTRODUCTION: Hearing protection devices are one of the primary noise reduction tools in developing countries. This study is intended to produce and apply acrylonitrile butadiene styrene (ABS)/clay nanocomposites to fabricate a laboratory single cup earmuffs and then compare it with double cup and s...

Descripción completa

Detalles Bibliográficos
Autores principales:	Ahmadi, Saeid, Nassiri, Parvin, Ghasemi, Ismaeil, Monazzam Ep, Mohammad R.
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	Canadian Center of Science and Education 2016
Materias:	Articles
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4804060/ https://www.ncbi.nlm.nih.gov/pubmed/26234977 http://dx.doi.org/10.5539/gjhs.v8n1p180

Ejemplares similares

Acoustic notch filtering earmuff utilizing Helmholtz resonator arrays
por: Mizukoshi, Fumiya, et al.
Publicado: (2021)

Motor Responses and Weight Gaining in Neonates through Use of Two Methods of Earmuff and Receiving Silence in NICU
por: Abdeyazdan, Z., et al.
Publicado: (2014)

Selection of Earmuffs and Other Personal Protective Equipment Used in Combination
por: Kozlowski, Emil, et al.
Publicado: (2019)

The effect of wearing an anti-flash hood on the noise attenuation of earmuffs
por: PADDAN, Gurmail S, et al.
Publicado: (2021)

Enhancer analysis of the Drosophila zinc finger transcription factor Earmuff by gene targeting
por: Hildebrandt, Kirsten, et al.
Publicado: (2021)

Comparison of speech intelligibility measures for an electronic amplifying earmuff and an identical passive attenuation device
por: Byrne, David C., et al.
Publicado: (2012)

The effects of earmuff on physiologic and motor responses in premature infants admitted in neonatal intensive care unit
por: Abdeyazdan, Zahra, et al.
Publicado: (2014)

Modeling Signal-to-Noise Ratio of Otoacoustic Emissions in Workers Exposed to Different Industrial Noise Levels
por: Nassiri, Parvin, et al.
Publicado: (2016)

Evaluation of the Effects of Various Sound Pressure Levels on the Level of Serum Aldosterone Concentration in Rats
por: Nassiri, Parvin, et al.
Publicado: (2017)

A Simple, Cost-effective, and Novel Method for Determining the Efficiency of Industrial and Commercial Noise-Canceling Earmuffs
por: Zangari, Shelby, et al.
Publicado: (2019)

PREOPERATIVE 3D MODELING AND PRINTING FOR GUIDING PERIACETABULAR OSTEOTOMY
por: Shelton, Trevor J., et al.
Publicado: (2021)

3D Printed Acoustically Programmable Soft Microactuators
por: Kaynak, Murat, et al.
Publicado: (2023)

Evaluation of the effects of occupational noise exposure on serum aldosterone and potassium among industrial workers
por: Zare, Sajad, et al.
Publicado: (2016)

Evaluation of Distortion Product Otoacoustic Emissions (DPOAEs) among workers at an Industrial Company exposed to different industrial noise levels in 2014
por: Zare, Sajad, et al.
Publicado: (2015)

3D Printing of PLA/clay Nanocomposites: Influence of Printing Temperature on Printed Samples Properties
por: Coppola, Bartolomeo, et al.
Publicado: (2018)

Fabrication of Capacitive Acoustic Resonators Combining 3D Printing and 2D Inkjet Printing Techniques
por: Haque, Rubaiyet Iftekharul, et al.
Publicado: (2015)

Effects of Earmuffs and Eye Masks on Propofol Sedation during Spinal Anesthesia for Orthopedic Surgery: A Randomized Controlled Trial
por: Park, Jin-Woo, et al.
Publicado: (2023)

Weighting Criteria and Prioritizing of Heat stress indices in surface mining using a Delphi Technique and Fuzzy AHP-TOPSIS Method
por: Asghari, Mehdi, et al.
Publicado: (2017)

Recent advancement in 3-D printing: nanocomposites with added functionality
por: Clarissa, Wu Hui-Yan, et al.
Publicado: (2021)

Addressable Acoustic Actuation of 3D Printed Soft Robotic Microsystems
por: Kaynak, Murat, et al.
Publicado: (2020)

A New Strategy for Achieving Shape Memory Effects in 4D Printed Two-Layer Composite Structures
por: Rahmatabadi, Davood, et al.
Publicado: (2022)

3D Printing and Shaping Polymers, Composites, and Nanocomposites: A Review
por: Azlin, M. N. M., et al.
Publicado: (2022)

PEG-Grafted Graphene/PLLA Nanocomposites: Effect of PEG Chain Length on Crystallization Kinetics of PLLA
por: Karimi, Samira, et al.
Publicado: (2022)

Application of Universal Thermal Climate Index (UTCI) for assessment of occupational heat stress in open-pit mines
por: NASSIRI, Parvin, et al.
Publicado: (2017)

Bio-inspired detoxification using 3D-printed hydrogel nanocomposites
por: Gou, Maling, et al.
Publicado: (2014)

3D Printing of Alginate-Natural Clay Hydrogel-Based Nanocomposites
por: Leu Alexa, Rebeca, et al.
Publicado: (2021)

Piezoresistive Properties of 3D-Printed Polylactic Acid (PLA) Nanocomposites
por: Hashemi Sanatgar, Razieh, et al.
Publicado: (2022)

Effectiveness of Earmuffs and Noise-cancelling Headphones for Coping with Hyper-reactivity to Auditory Stimuli in Children with Autism Spectrum Disorder: A Preliminary Study
por: Ikuta, Nobuhiko, et al.
Publicado: (2016)

Gold and silver dichroic nanocomposite in the quest for 3D printing the Lycurgus cup
por: Kool, Lars, et al.
Publicado: (2020)

Study of acoustic and aerodynamic performance of reactive silencer with different configurations: Theoretical, modeling and experimental
por: Rahimi Jokandan, Motaleb, et al.
Publicado: (2023)

Medical-Grade Polyamide 12 Nanocomposite Materials for Enhanced Mechanical and Antibacterial Performance in 3D Printing Applications
por: Vidakis, Nectarios, et al.
Publicado: (2022)

3D Printing of Ultrathin MXene toward Tough and Thermally Resistant Nanocomposites
por: Li, Yuewei, et al.
Publicado: (2022)

Acoustic Emissions in 3D Printed Parts under Mode I Delamination Test
por: Barile, Claudia, et al.
Publicado: (2018)

Evolvable Acoustic Field Generated by a Transducer with 3D-Printed Fresnel Lens
por: Wang, Danfeng, et al.
Publicado: (2021)

Investigation of the Biocidal Performance of Multi-Functional Resin/Copper Nanocomposites with Superior Mechanical Response in SLA 3D Printing
por: Vidakis, Nectarios, et al.
Publicado: (2022)

Nozzle Shape Guided Filler Orientation in 3D Printed Photo-curable Nanocomposites
por: Kim, Taeil, et al.
Publicado: (2018)

3D Printing of Metal/Metal Oxide Incorporated Thermoplastic Nanocomposites With Antimicrobial Properties
por: Abdullah, Turdimuhammad, et al.
Publicado: (2020)

Biodegradable Poly(Lactic Acid) Nanocomposites for Fused Deposition Modeling 3D Printing
por: Bardot, Madison, et al.
Publicado: (2020)

CNT-Type Dependent Cellular Adhesion on 3D-Printed Nanocomposite for Tissue Engineering
por: Mieloch, Adam A., et al.
Publicado: (2022)

Vat photopolymerization-based 3D printing of polymer nanocomposites: current trends and applications
por: Shah, Mussadiq, et al.
Publicado: (2023)

Cannot write session to /tmp/vufind_sessions/sess_me2a6rhkpksupbv4n20fac7ea8