Cargando…

Performance of High Layer Thickness in Selective Laser Melting of Ti6Al4V

To increase building rate and save cost, the selective laser melting (SLM) of Ti6Al4V with a high layer thickness (200 μm) and low cost coarse powders (53 μm–106 μm) at a laser power of 400 W is investigated in this preliminary study. A relatively large laser beam with a diameter of 200 μm is utiliz...

Descripción completa

Detalles Bibliográficos
Autores principales:	Shi, Xuezhi, Ma, Shuyuan, Liu, Changmeng, Chen, Cheng, Wu, Qianru, Chen, Xianping, Lu, Jiping
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2016
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC5456986/ https://www.ncbi.nlm.nih.gov/pubmed/28774097 http://dx.doi.org/10.3390/ma9120975

Ejemplares similares

Beam Diameter Dependence of Performance in Thick-Layer and High-Power Selective Laser Melting of Ti-6Al-4V
por: Shi, Wentian, et al.
Publicado: (2018)

Effect of Molten Pool Size on Microstructure and Tensile Properties of Wire Arc Additive Manufacturing of Ti-6Al-4V Alloy
por: Wu, Qianru, et al.
Publicado: (2017)

Wetting and Spreading of AgCuTi on Selective Laser-Melted Ti-6Al-4V
por: Hao, Lujing, et al.
Publicado: (2021)

Investigation on Morphology and Mechanical Properties of Rod Units in Lattice Structures Fabricated by Selective Laser Melting
por: Jing, Chenchen, et al.
Publicado: (2021)

Research on High Layer Thickness Fabricated of 316L by Selective Laser Melting
por: Wang, Shuo, et al.
Publicado: (2017)

Interface Characterization of Bimetallic Ti-6Al-4V/Ti2AlNb Structures Prepared by Selective Laser Melting
por: Polozov, Igor, et al.
Publicado: (2022)

Manufacturing and Characterization of Ti6Al4V Lattice Components Manufactured by Selective Laser Melting
por: Campanelli, Sabina L., et al.
Publicado: (2014)

A Numerical Study on the Mesoscopic Characteristics of Ti-6Al-4V by Selective Laser Melting
por: Ao, Xiaohui, et al.
Publicado: (2022)

Wire Arc Additive Manufacturing of AZ31 Magnesium Alloy: Grain Refinement by Adjusting Pulse Frequency
por: Guo, Jing, et al.
Publicado: (2016)

Effect of Laser Rescanning on the Characteristics and Residual Stress of Selective Laser Melted Titanium Ti6Al4V Alloy
por: Miao, Xiaojin, et al.
Publicado: (2020)

The Martensitic Transformation and Mechanical Properties of Ti6Al4V Prepared via Selective Laser Melting
por: He, Junjie, et al.
Publicado: (2019)

Fatigue of Ti6Al4V Structural Health Monitoring Systems Produced by Selective Laser Melting
por: Strantza, Maria, et al.
Publicado: (2016)

Slurry Erosion–Corrosion Characteristics of As-Built Ti-6Al-4V Manufactured by Selective Laser Melting
por: Aldahash, Saleh Ahmed, et al.
Publicado: (2020)

A Further Analysis on Ti6Al4V Lattice Structures Manufactured by Selective Laser Melting
por: Maietta, Saverio, et al.
Publicado: (2019)

Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)
por: Pasang, Tim, et al.
Publicado: (2021)

Effects of Process Parameters on the Corrosion Resistance and Biocompatibility of Ti6Al4V Parts Fabricated by Selective Laser Melting
por: Xiang, Shibo, et al.
Publicado: (2022)

Effect of Layer Thickness in Selective Laser Melting on Microstructure of Al/5 wt.%Fe(2)O(3) Powder Consolidated Parts
por: Dadbakhsh, Sasan, et al.
Publicado: (2014)

Research on Residual Stresses and Microstructures of Selective Laser Melted Ti6Al4V Treated by Thermal Vibration Stress Relief
por: Chen, Shuguang, et al.
Publicado: (2023)

Single tracks data obtained by selective laser melting of Ti6Al4V with a small laser spot diameter
por: Vaglio, Emanuele, et al.
Publicado: (2020)

Selective Laser Melting and Electron Beam Melting of Ti6Al4V for Orthopedic Applications: A Comparative Study on the Applied Building Direction
por: Ginestra, Paola, et al.
Publicado: (2020)

Digitally Fabricated Dentures for Full Mouth Rehabilitation with Zirconia, Polyetheretherketone and Selective Laser Melted Ti-6Al-4V Material
por: Lee, Wei-Ting, et al.
Publicado: (2022)

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V
por: Ali, Haider, et al.
Publicado: (2018)

Customized a Ti6Al4V Bone Plate for Complex Pelvic Fracture by Selective Laser Melting
por: Wang, Di, et al.
Publicado: (2017)

Physical–Mechanical Characteristics and Microstructure of Ti6Al7Nb Lattice Structures Manufactured by Selective Laser Melting
por: Cosma, Cosmin, et al.
Publicado: (2020)

Analysis of Microstructure and Properties of a Ti–AlN Composite Produced by Selective Laser Melting
por: Sitek, Ryszard, et al.
Publicado: (2020)

Effects of Laser Shock Peening on Microstructure and Properties of Ti–6Al–4V Titanium Alloy Fabricated via Selective Laser Melting
por: Lan, Liang, et al.
Publicado: (2020)

Study on Topology Optimization Design, Manufacturability, and Performance Evaluation of Ti-6Al-4V Porous Structures Fabricated by Selective Laser Melting (SLM)
por: Xu, Yangli, et al.
Publicado: (2017)

Work Hardening of Heat-Treated AlSi10Mg Alloy Manufactured by Single and Double Laser Selective Laser Melting: Effects of Layer Thickness and Hatch Spacing
por: Ghio, Emanuele, et al.
Publicado: (2021)

Influence of Ultrasonic Surface Rolling on Microstructure and Wear Behavior of Selective Laser Melted Ti-6Al-4V Alloy
por: Wang, Zhen, et al.
Publicado: (2017)

The Effects of Feature Sizes in Selectively Laser Melted Ti-6Al-4V Parts on the Validity of Optimised Process Parameters
por: Phutela, Chinmay, et al.
Publicado: (2019)

The effect of oxygen pickup during selective laser melting on the microstructure and mechanical properties of Ti–6Al–4V lattices
por: Velasco-Castro, M., et al.
Publicado: (2019)

Enhanced Osseointegration by the Hierarchical Micro-Nano Topography on Selective Laser Melting Ti-6Al-4V Dental Implants
por: Shu, Tianyu, et al.
Publicado: (2021)

Effects of Annealing and Solution Treatments on the Microstructure and Mechanical Properties of Ti6Al4V Manufactured by Selective Laser Melting
por: Jaber, Hassanen, et al.
Publicado: (2022)

Bioactive and antimicrobial macro-/micro-nanoporous selective laser melted Ti–6Al–4V alloy for biomedical applications
por: Rajendran, Archana, et al.
Publicado: (2022)

Optimisation of Selective Laser Melted Ti6Al4V Functionally Graded Lattice Structures Accounting for Structural Safety
por: Zhu, Lei, et al.
Publicado: (2022)

Influence of the thermal-fluid behavior on the microstructure evolution during the process of selective laser melting of Ti6Al4V
por: Zeng, Chao, et al.
Publicado: (2022)

Densification, Tailored Microstructure, and Mechanical Properties of Selective Laser Melted Ti–6Al–4V Alloy via Annealing Heat Treatment
por: Wang, Di, et al.
Publicado: (2022)

Uncertainties Induced by Processing Parameter Variation in Selective Laser Melting of Ti6Al4V Revealed by In-Situ X-ray Imaging
por: Young, Zachary A., et al.
Publicado: (2022)

Selective Laser Melting Produced Ti-6Al-4V: Post-Process Heat Treatments to Achieve Superior Tensile Properties
por: Ter Haar, Gerrit M., et al.
Publicado: (2018)

Investigation into using resonant frequency measurements to predict the mechanical properties of Ti-6Al-4V manufactured by selective laser melting
por: Todd, Mark A., et al.
Publicado: (2019)

Cannot write session to /tmp/vufind_sessions/sess_bmbbufe3ugin1aj256m9ugbg8g