Cargando…

Effect of Injection Molding Melt Temperatures on PLGA Craniofacial Plate Properties during In Vitro Degradation

The purpose of this article is to present mechanical and physicochemical properties during in vitro degradation of PLGA material as craniofacial plates based on different values of injection molded temperatures. Injection molded plates were submitted to in vitro degradation in a thermostat bath at 3...

Descripción completa

Detalles Bibliográficos
Autores principales:	de Melo, Liliane Pimenta, Salmoria, Gean Vitor, Fancello, Eduardo Alberto, Roesler, Carlos Rodrigo de Mello
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	Hindawi 2017
Materias:	Research Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC5606095/ https://www.ncbi.nlm.nih.gov/pubmed/29056968 http://dx.doi.org/10.1155/2017/1256537

Ejemplares similares

Influence of Processing Conditions on the Mechanical Behavior and Morphology of Injection Molded Poly(lactic-co-glycolic acid) 85:15
por: de Melo, Liliane Pimenta, et al.
Publicado: (2017)

Influence of Breast Implant Surface Finishing on Physicochemical and Mechanical Properties before and after Extreme Degradation Studies
por: de Mello Gindri, Izabelle, et al.
Publicado: (2021)

Analysis of Melt Front Behavior of a Light Guiding Plate during the Filling Phase of Micro-Injection Molding
por: Lin, Wei-Chun, et al.
Publicado: (2022)

Modeling and Experimental Studies on Polymer Melting and Flow in Injection Molding
por: Wilczyński, Krzysztof, et al.
Publicado: (2022)

Immobilization of Active Antibodies at Polymer Melt Surfaces during Injection Molding
por: Hobæk, Thor Christian, et al.
Publicado: (2022)

3D-Printed EVA Devices for Antiviral Delivery and Herpes Virus Control in Genital Infection
por: de Carvalho Rodrigues, Victor, et al.
Publicado: (2022)

Melt Temperature Estimation by Machine Learning Model Based on Energy Flow in Injection Molding
por: Jeon, Joohyeong, et al.
Publicado: (2022)

Importance of Melt Flow Direction during Injection Molding on Polymer Heat Sinks’ Cooling Efficiency
por: Guzej, Michal, et al.
Publicado: (2021)

Fabrication of Micro-Structured LED Diffusion Plate Using Efficient Micro Injection Molding and Micro-Ground Mold Core
por: Lu, Yanjun, et al.
Publicado: (2020)

Enhanced Injection Molding Simulation of Advanced Injection Molds
por: Zink, Béla, et al.
Publicado: (2017)

Molecular Insights into the Wall Slip Behavior of Pseudoplastic Polymer Melt in Nanochannels during Micro Injection Molding
por: Wu, Wangqing, et al.
Publicado: (2022)

Development of Metal Plate with Internal Structure Utilizing the Metal Injection Molding (MIM) Process
por: Shin, Kwangho, et al.
Publicado: (2013)

Effects of Heating and Cooling of Injection Mold Cavity Surface and Melt Flow Control on Properties of Carbon Fiber Reinforced Semi-Aromatic Polyamide Molded Products
por: Murata, Yasuhiko, et al.
Publicado: (2021)

High-Precision Thin Wall Bipolar Plates for Fuel Cell Applications via Injection Compression Molding with Dynamic Mold Temperature Control
por: Roth, Benedikt, et al.
Publicado: (2022)

Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
por: Lin, Chung-Chih, et al.
Publicado: (2020)

Ductility and Toughness Improvement of Injection-Molded Compostable Pieces of Polylactide by Melt Blending with Poly(ε-caprolactone) and Thermoplastic Starch
por: Quiles-Carrillo, Luis, et al.
Publicado: (2018)

A Multiscale Simulation of Polymer Melt Injection Molding Filling Flow Using SPH Method with Slip-Link Model
por: Ren, Mengke, et al.
Publicado: (2022)

Optimized Micro-Pattern Design and Fabrication of a Light Guide Plate Using Micro-Injection Molding
por: Fan, Fang-Yu, et al.
Publicado: (2021)

Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding
por: Li, Jiquan, et al.
Publicado: (2021)

In-Mold Sensors for Injection Molding: On the Way to Industry 4.0
por: Ageyeva, Tatyana, et al.
Publicado: (2019)

Multiple In-Mold Sensors for Quality and Process Control in Injection Molding
por: Párizs, Richárd Dominik, et al.
Publicado: (2023)

Handbook of metal injection molding
por: Heaney, Donald F.
Publicado: (2012)

Thermoelasticity of Injection-Molded Parts
por: Turk, Janez, et al.
Publicado: (2023)

Universal Digital High Resolution Melt for the detection of pulmonary mold infections
por: Goshia, Tyler, et al.
Publicado: (2023)

Analysis of Weld Lines in Micro-Injection Molding
por: Liparoti, Sara, et al.
Publicado: (2023)

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites
por: Wang, Jian, et al.
Publicado: (2021)

Tissue Engineering Scaffolds Fabricated in Dissolvable 3D-Printed Molds for Patient-Specific Craniofacial Bone Regeneration
por: de la Lastra, Angela Alarcon, et al.
Publicado: (2018)

Hydrophobicity Tuning by the Fast Evolution of Mold Temperature during Injection Molding
por: Liparoti, Sara, et al.
Publicado: (2018)

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene
por: Liparoti, Sara, et al.
Publicado: (2020)

Micro Injection Molding of Thin Cavities Using Stereolithography for Mold Fabrication
por: Surace, Rossella, et al.
Publicado: (2021)

Post-Molding Shrinkage, Structure and Properties of Cellular Injection-Molded Polypropylene
por: Kościuszko, Artur, et al.
Publicado: (2022)

Pressure Analysis of Dynamic Injection Molding and Process Parameter Optimization for Reducing Warpage of Injection Molded Products
por: Wang, Xinyu, et al.
Publicado: (2017)

Manufacturing Signatures of Injection Molding and Injection Compression Molding for Micro-Structured Polymer Fresnel Lens Production
por: Loaldi, Dario, et al.
Publicado: (2018)

Injectable In-Situ Forming Depot Based on PLGA and PLGA-PEG-PLGA for Sustained-Release of Risperidone: In Vitro Evaluation and Pharmacokinetics in Rabbits
por: Rezaeian Shiadeh, Seyedeh Nesa, et al.
Publicado: (2023)

Accuracy Assessment of Molded, Patient-Specific Polymethylmethacrylate Craniofacial Implants Compared to Their 3D Printed Originals
por: Chamo, Dave, et al.
Publicado: (2020)

Response of ATLAS Injection Molded Scintillators
por: Jankowski, D, et al.
Publicado: (1994)

Injection Molding Plastic Solar Cells
por: Burgués‐Ceballos, Ignasi, et al.
Publicado: (2023)

Advanced Injection Molding Methods: Review
por: Czepiel, Mateusz, et al.
Publicado: (2023)

Modeling and Analysis of Morphology of Injection Molding Polypropylene Parts Induced by In-Mold Annealing
por: Salomone, Rita, et al.
Publicado: (2022)

The Low Breaking Fiber Mechanism and Its Effect on the Behavior of the Melt Flow of Injection Molded Ultra-Long Glass Fiber Reinforced Polypropylene Composites
por: Huang, Po-Wei, et al.
Publicado: (2021)

Cannot write session to /tmp/vufind_sessions/sess_4naierg1bf39rl1q6lgd839lnq