Cargando…

Prediction of Surface Roughness considering Cutting Parameters and Humidity Condition in End Milling of Polyamide Materials

To know the impact of processing parameters of PA6G under different humidity conditions is important as it is vulnerable to humidity up to 7 %. This study investigated the effect of cutting parameters to surface roughness quality in wet and dry conditions. Artificial Neural Network (ANN) modeling is...

Descripción completa

Detalles Bibliográficos
Autor principal:	Bozdemir, Mustafa
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	Hindawi 2018
Materias:	Research Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6046151/ https://www.ncbi.nlm.nih.gov/pubmed/30050565 http://dx.doi.org/10.1155/2018/5850432

Ejemplares similares

Optimization of Machining Parameters to Minimize Cutting Forces and Surface Roughness in Micro-Milling of Mg13Sn Alloy
por: Ercetin, Ali, et al.
Publicado: (2023)

Effect of Milling Processing Parameters on the Surface Roughness and Tool Cutting Forces of T2 Pure Copper
por: Lai, Fuqiang, et al.
Publicado: (2023)

Evolutionary Optimization of Machining Parameters Based on Surface Roughness in End Milling of Hot Rolled Steel
por: Abu-Mahfouz, Issam, et al.
Publicado: (2021)

Response Ant Colony Optimization of End Milling Surface Roughness
por: Kadirgama, K., et al.
Publicado: (2010)

Influence of the Milling Conditions of Aluminium Alloy 2017A on the Surface Roughness
por: Nowakowski, Lukasz, et al.
Publicado: (2022)

Effects of Machining Parameters and Tool Reconditioning on Cutting Force, Tool Wear, Surface Roughness and Burr Formation in Nickel-Based Alloy Milling
por: Kónya, Gábor, et al.
Publicado: (2023)

Modeling of Surface Topography after Milling with a Lens-Shaped End-Mill, Considering Runout
por: Żurawski, Karol, et al.
Publicado: (2022)

Influence of the Tool Cutting Edge Helix Angle on the Surface Roughness after Finish Milling of Magnesium Alloys
por: Zagórski, Ireneusz, et al.
Publicado: (2022)

Milling Surface Roughness Prediction Based on Physics-Informed Machine Learning
por: Zeng, Shi, et al.
Publicado: (2023)

Optimization of Cutting Data and Tool Inclination Angles During Hard Milling with CBN Tools, Based on Force Predictions and Surface Roughness Measurements
por: Matras, Andrzej, et al.
Publicado: (2020)

Investigation of the Effect of End Mill-Geometry on Roughness and Surface Strain-Hardening of Aluminum Alloy AA6082
por: Filippov, Pavel, et al.
Publicado: (2020)

Roughness Control of Surfaces Using a Laser Profilometer with the Selected Material Cutting Technology
por: Ružbarský, Juraj
Publicado: (2023)

The Effect of Clearance Angle on Tool Life, Cutting Forces, Surface Roughness, and Delamination during Carbon-Fiber-Reinforced Plastic Milling
por: Knápek, Tomáš, et al.
Publicado: (2023)

Experimental Investigation of Surface Roughness in Milling of Duralcan(TM) Composite
por: Wiciak-Pikuła, Martyna, et al.
Publicado: (2021)

Spiral Bevel Gears Face Roughness Prediction Produced by CNC End Milling Centers
por: Álvarez, Álvaro, et al.
Publicado: (2018)

Prediction of Parameters of Equivalent Sum Rough Surfaces
por: Pawlus, Pawel, et al.
Publicado: (2020)

Evaluation of Surface Roughness Parameters of HDF for Finishing under Industrial Conditions
por: Henke, Milena, et al.
Publicado: (2022)

Temperature Field of Tool Engaged Cutting Zone for Milling of Titanium Alloy with Ball-End Milling
por: Yang, Shucai, et al.
Publicado: (2018)

Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel
por: Kuntoğlu, Mustafa, et al.
Publicado: (2020)

Multiple Sensor Monitoring of CFRP Drilling to Define Cutting Parameters Sensitivity on Surface Roughness, Cylindricity and Diameter
por: Álvarez-Alcón, Miguel, et al.
Publicado: (2020)

Correlation Study of 3D Surface Roughness of Milled Surfaces with Laser Speckle Pattern
por: Jayabarathi, Suganandha Bharathi, et al.
Publicado: (2022)

Generic Cutting Force Modeling with Comprehensively Considering Tool Edge Radius, Tool Flank Wear and Tool Runout in Micro-End Milling
por: Gao, Shuaishuai, et al.
Publicado: (2022)

Analysis of Vibration, Deflection Angle and Surface Roughness in Water-Jet Cutting of AZ91D Magnesium Alloy and Simulation of Selected Surface Roughness Parameters Using ANN
por: Biruk-Urban, Katarzyna, et al.
Publicado: (2023)

Force Prediction and Cutting-Parameter Optimization in Micro-Milling Al7075-T6 Based on Response Surface Method
por: Zhou, Menghua, et al.
Publicado: (2020)

Online Surface Roughness Prediction for Assembly Interfaces of Vertical Tail Integrating Tool Wear under Variable Cutting Parameters
por: Wang, Yahui, et al.
Publicado: (2022)

Parametric Optimization of Trochoidal Step on Surface Roughness and Dish Angle in End Milling of AISID3 Steel Using Precise Measurements
por: J, Santhakumar, et al.
Publicado: (2019)

An Experimental Investigation on Micro End Milling with High-Speed Up Cut Milling for Hardened Die Steel
por: Kino, Haruki, et al.
Publicado: (2020)

Surface Roughness after Milling of the Al/CFRP Stacks with a Diamond Tool
por: Doluk, Elżbieta, et al.
Publicado: (2021)

High-Performance Face Milling of 42CrMo4 Steel: Influence of Entering Angle on the Measured Surface Roughness, Cutting Force and Vibration Amplitude
por: Płodzień, Marcin, et al.
Publicado: (2021)

Surface Roughness Prediction in Ultra-Precision Milling: An Extreme Learning Machine Method with Data Fusion
por: Shang, Suiyan, et al.
Publicado: (2023)

The Influence of Tool Path Strategies on Cutting Force and Surface Texture during Ball End Milling of Low Curvature Convex Surfaces
por: Shajari, Shaghayegh, et al.
Publicado: (2014)

Surface Roughness Optimization of Polyamide-6/Nanoclay Nanocomposites Using Artificial Neural Network: Genetic Algorithm Approach
por: Moghri, Mehdi, et al.
Publicado: (2014)

Surface Roughness Effects on the Vibration Characteristics of AT-Cut Quartz Crystal Plate
por: Li, Mengjie, et al.
Publicado: (2023)

Prediction of Surface Roughness of an Abrasive Water Jet Cut Using an Artificial Neural Network
por: Ficko, Mirko, et al.
Publicado: (2021)

Optimization of Cutting Parameters in Turning of Titanium Alloy (Grade 5) by Analysing Surface Roughness, Tool Wear and Energy Consumption
por: Akkuş, H., et al.
Publicado: (2021)

Efficient Prediction of Stability Boundaries in Milling Considering the Variation of Tool Features and Workpiece Materials
por: Sun, Huijuan, et al.
Publicado: (2023)

Experimental Investigation of Cutting Vibration during Micro-End-Milling of the Straight Groove
por: Ma, Lijie, et al.
Publicado: (2020)

Prediction of surface roughness based on fused features and ISSA-DBN in milling of die steel P20
por: Guo, Miaoxian, et al.
Publicado: (2023)

Ferroelectric switching in ferroelastic materials with rough surfaces
por: Lu, Guangming, et al.
Publicado: (2019)

Statistical Analysis of Machining Parameters on Burr Formation, Surface Roughness and Energy Consumption during Milling of Aluminium Alloy Al 6061-T6
por: Zaidi, Sajid Raza, et al.
Publicado: (2022)

Cannot write session to /tmp/vufind_sessions/sess_pnj1oes4oqfcl6capp2vej9m60