Cargando…

Research and Development of a 3D Jet Printer for High-Viscosity Molten Liquids

Micro-droplet jetting manufacture is a new 3D printing technology developed in recent years. Presently, this new technology mainly aims at ejecting a low-viscosity medium. Therefore, a device for ejecting high-viscosity molten liquid is designed by analyzing the injection principle of high-viscosity...

Descripción completa

Detalles Bibliográficos
Autores principales:	Yang, Yang, Gu, Shoudong, Liu, Jianfang, Tian, Hongyu, Lv, Qingqing
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2018
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6266737/ https://www.ncbi.nlm.nih.gov/pubmed/30715053 http://dx.doi.org/10.3390/mi9110554

Ejemplares similares

Patterning of High-Viscosity Silver Paste by an Electrohydrodynamic-Jet Printer for Use in TFT Applications
por: Can, Thi Thu Thuy, et al.
Publicado: (2019)

Design and Experiment of a Solder Paste Jetting System Driven by a Piezoelectric Stack
por: Gu, Shoudong, et al.
Publicado: (2016)

Development of Photo-Polymerization-Type 3D Printer for High-Viscosity Ceramic Resin Using CNN-Based Surface Defect Detection
por: Chung, Jin-Kyo, et al.
Publicado: (2023)

Retrieving Equivalent Shear Viscosity for Molten Polymers from 3-D Nonisothermal Capillary Flow Simulation
por: Wen, Yu-Ho, et al.
Publicado: (2021)

Dynamic Viscosity of the NaF-KF-NdF(3) Molten System
por: Rudenko, Alexei, et al.
Publicado: (2022)

Examining the influence of turbulence on viscosity measurements of molten germanium under reduced gravity
por: Bracker, G. P., et al.
Publicado: (2022)

Practical 3D printers
por: Evans, Brian
Publicado: (2012)

Publisher Correction: Examining the influence of turbulence on viscosity measurements of molten germanium under reduced gravity
por: Bracker, G. P., et al.
Publicado: (2023)

3D printing with Delta printers
por: Bell, Charles A
Publicado: (2015)

3D Printers Enter the Kitchen
por: Katsnelson, Alla
Publicado: (2021)

High-performance polymer 3D printing – Open-source liquid cooled scalable printer design
por: Birkelid, Andreas Hagerup, et al.
Publicado: (2022)

Experimental Study of the Jetting Behavior of High-Viscosity Nanosilver Inks in Inkjet-Based 3D Printing
por: Xiao, Xingzhi, et al.
Publicado: (2022)

Evaluation of Lateral and Vertical Dimensions of Micromolds Fabricated by a PolyJet™ Printer
por: Vijayan, Sindhu, et al.
Publicado: (2021)

Continuous spinning aligned liquid crystal elastomer fibers with a 3D printer setup
por: Lin, Xueyan, et al.
Publicado: (2021)

HistoEnder: A 3D printer-based histological slide autostainer that retains 3D printer functions
por: Ponzetti, Marco, et al.
Publicado: (2022)

Assessment and Mitigation of Exposure of 3-D Printer Emissions
por: Kim, Boowook, et al.
Publicado: (2022)

Development of breast phantoms using a 3D printer and glandular dose evaluation
por: Lee, Dong‐Yeon, et al.
Publicado: (2021)

PRINTER TEST
por: Albert, J N
Publicado: (1988)

Printers’ Diseases
Publicado: (1860)

Dynamic catcher for stabilization of high-viscosity extrusion jets
por: Doak, R. Bruce, et al.
Publicado: (2023)

International Conference on ionic liquids, molten salts and polyelectrolytes
por: Bennemann, K -H, et al.
Publicado: (1982)

Ionic liquid properties: from molten salts to RTILs
por: Marcus, Yizhak
Publicado: (2016)

Ionic Liquids: Just Molten Salts After All?
por: Yau, Hon Man, et al.
Publicado: (2009)

Development of a 3D printer using scanning projection stereolithography
por: Lee, Michael P., et al.
Publicado: (2015)

Maintaining and troubleshooting your 3D printer
por: Bell, Charles
Publicado: (2014)

3D-printer visualization of neuron models
por: McDougal, Robert A., et al.
Publicado: (2015)

Monitoring the Calibration of In-Office 3D Printers
por: Mukherjee, Esha, et al.
Publicado: (2023)

Design and Synthesis of Free-Radical/Cationic Photosensitive Resin Applied for 3D Printer with Liquid Crystal Display (LCD) Irradiation
por: Shan, Junyang, et al.
Publicado: (2020)

Fluid Gels: a New Feedstock for High Viscosity Jetting
por: Holland, Sonia, et al.
Publicado: (2018)

A Study on the Correlation between Change in the Geometrical Dimension of a Free-Falling Molten Glass Gob and Its Viscosity
por: Hussain, Mazhar, et al.
Publicado: (2022)

Development of a 3D Printer for the Manufacture of Functional Food Protein Gels
por: Portanguen, Stéphane, et al.
Publicado: (2022)

A 3D Printer Guide for the Development and Application of Electrochemical Cells and Devices
por: Silva, Ana Luisa, et al.
Publicado: (2021)

Development of a Multi-Material 3D Printer for Functional Anatomic Models
por: Jaksa, Laszlo, et al.
Publicado: (2021)

Development of affordable 3D food printer with an exchangeable syringe-pump mechanism
por: Demircan, Evren, et al.
Publicado: (2023)

Printer TV Hardcopy
por: Gueugnon, D
Publicado: (1985)

Errata (Printer's correction)
Publicado: (2016)

Abstract: 3D Domestic Printer Use in Rhinoplasty
por: Valente, Denis souto, et al.
Publicado: (2017)

Viscosity of pure organic liquids and binary liquid mixtures
por: Lechner, M
Publicado: (2001)

Viscosity of pure organic liquids and binary liquid mixtures
por: Lechner, M
Publicado: (2002)

Proposal for universality in the viscosity of metallic liquids
por: Blodgett, M. E., et al.
Publicado: (2015)

Cannot write session to /tmp/vufind_sessions/sess_11obi9dt5jogsrv0jp5le9cstk