Cargando…

Modification of Residual Stresses in Laser Additive Manufactured AlSi10Mg Specimens Using an Ultrasonic Peening Technique

Ultrasonic peening treatment (UPT) has been proved to be an effective way of improving residual stresses distribution in weld structures. Thus, it shows a great potential in stress modification for metal parts fabricated by additive manufacturing technology. In this paper, an investigation into the...

Descripción completa

Detalles Bibliográficos
Autores principales:	Xing, Xiaodong, Duan, Xiaoming, Sun, Xiaojing, Gong, Haijun, Wang, Liquan, Jiang, Fengchun
Formato:	Online Artículo Texto
Lenguaje:	English
Publicado:	MDPI 2019
Materias:	Article
Acceso en línea:	https://www.ncbi.nlm.nih.gov/pmc/articles/PMC6384986/ https://www.ncbi.nlm.nih.gov/pubmed/30717209 http://dx.doi.org/10.3390/ma12030455

Ejemplares similares

Investigation of Surface Integrity of Selective Laser Melting Additively Manufactured AlSi10Mg Alloy under Ultrasonic Elliptical Vibration-Assisted Ultra-Precision Cutting
por: Tan, Rongkai, et al.
Publicado: (2022)

Effective Mechanical Properties of AlSi7Mg Additively Manufactured Cubic Lattice Structures
por: Mantovani, Sara, et al.
Publicado: (2022)

Surface Topographic Features after Milling of Additively Manufactured AlSi10Mg Aluminum Alloy
por: Struzikiewicz, Grzegorz, et al.
Publicado: (2022)

A Comparative Study of Corrosion AA6061 and AlSi10Mg Alloys Produced by Extruded and Additive Manufacturing
por: Estupiñan-López, Francisco, et al.
Publicado: (2021)

Comparison of Various Intrinsic Defect Criteria to Plot Kitagawa–Takahashi Diagrams in Additively Manufactured AlSi10Mg
por: Nur, Mohammed Intishar, et al.
Publicado: (2023)

FEM Simulation of AlSi10Mg Artifact for Additive Manufacturing Process Calibration with Industrial-Computed Tomography Validation
por: Patuelli, Cesare, et al.
Publicado: (2023)

Experimental Determination of Residual Stresses Generated by Single Point Incremental Forming of AlSi10Mg Sheets Produced Using SLM Additive Manufacturing Process
por: López, Cecilio, et al.
Publicado: (2018)

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures
por: Nammalvar Raja Rajan, Aravindh, et al.
Publicado: (2022)

Aging Profiles of AlSi7Mg0.6 and AlSi10Mg0.3 Alloys Manufactured via Laser-Powder Bed Fusion: Direct Aging versus T6
por: Cerri, Emanuela, et al.
Publicado: (2022)

In-Situ Laser Polishing Additive Manufactured AlSi10Mg: Effect of Laser Polishing Strategy on Surface Morphology, Roughness and Microhardness
por: Zhou, Jiantao, et al.
Publicado: (2021)

Corrosion Behavior of Heat-Treated AlSi10Mg Manufactured by Laser Powder Bed Fusion
por: Cabrini, Marina, et al.
Publicado: (2018)

Strength and Cyclic Properties of Additive vs. Conventionally Produced Material AlSi(10)Mg
por: Chmelko, Vladimír, et al.
Publicado: (2023)

Eigenstrain reconstruction of residual strains in an additively manufactured and shot peened nickel superalloy compressor blade
por: Salvati, E, et al.
Publicado: (2017)

A Comprehensive Approach to Powder Feedstock Characterization for Powder Bed Fusion Additive Manufacturing: A Case Study on AlSi7Mg
por: Muñiz-Lerma, Jose Alberto, et al.
Publicado: (2018)

High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing
por: Lehmhus, Dirk, et al.
Publicado: (2022)

Laser Additive Manufacturing of TC4/AlSi12 Bimetallic Structure via Nb Interlayer
por: Jing, Zhicheng, et al.
Publicado: (2022)

Laser Peening Process and Its Impact on Materials Properties in Comparison with Shot Peening and Ultrasonic Impact Peening
por: Gujba, Abdullahi K., et al.
Publicado: (2014)

Optimization of Heat Treatment Parameters of AlSi7Mg Alloy
por: Pezda, Jacek
Publicado: (2022)

Data on mechanical properties of open-cell AlSi10Mg materials and open-cell AlSi10Mg-SiC composites with different pore sizes and strain rates
por: Kolev, Mihail, et al.
Publicado: (2023)

Damage Progress Classification in AlSi10Mg SLM Specimens by Convolutional Neural Network and k-Fold Cross Validation
por: Barile, Claudia, et al.
Publicado: (2022)

Failure Analysis of the Tree Column Structures Type AlSi10Mg Alloy Branches Manufactured by Selective Laser Melting
por: Bai, Peikang, et al.
Publicado: (2020)

Effect of Heat Treatment on Gradient Microstructure of AlSi10Mg Lattice Structure Manufactured by Laser Powder Bed Fusion
por: Liu, Mulin, et al.
Publicado: (2020)

Microstructural Characteristics of Al-Ti-B Inoculation Wires and Their Addition to the AlSi7Mg0.3 Alloy
por: Knaislová, Anna, et al.
Publicado: (2022)

Effects of Power and Laser Speed on the Mechanical Properties of AlSi7Mg0.6 Manufactured by Laser Powder Bed Fusion
por: Vaudreuil, Sébastien, et al.
Publicado: (2022)

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)
por: Yang, Qingfeng, et al.
Publicado: (2019)

Effect of Ultrasonic Shot Peening and Laser Shock Peening on the Microstructure and Microhardness of IN738LC Alloys
por: Liu, Sijia, et al.
Publicado: (2023)

Microstructure Evolution of AlSi10Mg(Cu) Alloy Related to Isothermal Exposure
por: Cai, Cheng, et al.
Publicado: (2018)

Fretting Fatigue Experiment and Analysis of AlSi9Cu2Mg Alloy
por: Wang, Jun, et al.
Publicado: (2016)

Research on Microstructure and Properties of AlSi10Mg Fabricated by Selective Laser Melting
por: Pan, Wei, et al.
Publicado: (2022)

Sustainability of compressive residual stress on the processing time of water jet peening using ultrasonic power
por: Ijiri, Masataka, et al.
Publicado: (2018)

Nondestructive Evaluation of Residual Stress in Shot Peened Inconel Using Ultrasonic Minimum Reflection Measurement
por: Choi, Yeong-Won, et al.
Publicado: (2023)

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects
por: Ghio, Emanuele, et al.
Publicado: (2022)

Microstructure and Mechanical Properties of Nanoparticulate Y(2)O(3) Modified AlSi10Mg Alloys Manufactured by Selective Laser Melting
por: Zhang, Fuxu, et al.
Publicado: (2023)

PBF-LB Process-Induced Regular Cavities for Lightweight AlSi10Mg Structures
por: Lubkowitz, Victor, et al.
Publicado: (2021)

Investigation and Optimization of the SLM and WEDM Processes’ Parameters for the AlSi10Mg-Sintered Part
por: Franczyk, Emilia, et al.
Publicado: (2021)

AlSi10Mg in Powder Bed Fusion with Laser Beam: An Old and Boring Material?
por: Rasch, Michael, et al.
Publicado: (2022)

Corrosion-Fatigue Performance of 3D-Printed (L-PBF) AlSi10Mg
por: Linder, Clara, et al.
Publicado: (2023)

Microstructure and Mechanical Properties of TiB(2)/AlSi7Mg0.6 Composites Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)
por: Yang, Qingfeng, et al.
Publicado: (2022)

Performance Consistency of AlSi10Mg Alloy Manufactured by Simulating Multi Laser Beam Selective Laser Melting (SLM): Microstructures and Mechanical Properties
por: Liu, Bin, et al.
Publicado: (2018)

Effects of the Combined Addition of Zn and Mg on Corrosion Behaviors of Electropainted AlSi-Based Metallic Coatings Used for Hot-Stamping Steel Sheets
por: Kim, Si On, et al.
Publicado: (2020)

Cannot write session to /tmp/vufind_sessions/sess_3s0esgij3980lr8qv62ur9lst8